Roland AX-EDGE Parameter Guide

System Parameters
37
CTRL RIBBON
You can specify whether the CTRL RIBBON settings follow the
settings of the currently selected program or follow the system
settings.
If the currently selected program’s CTRL RIBBON: Source parameter
is set to “SYS,” the system settings are used.
Parameter
[K] [J] button
Value
[-] [+] Buttons
Explanation
Posi
(Position Function)
Specifies the function that is assigned to the ribbon controller
(left/right axis) when program’s CTRL RIBBON: Source is set
to “SYS.”
OFF No function is assigned.
CC01–31, 32 (OFF),
33–95
Controller number 1–31, 32, 33–95
AFT Aftertouch
PITCH BEND Raise or lower the pitch.
PART FADE1
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
PART FADE2
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
Pres (Pressure Function)
Specifies the function when the ribbon controller is pressed
(pressure axis).
OFF No function is assigned.
CC01–31, 32 (OFF),
33–95
Controller number 1–31, 32, 33–95
* CC74 (Cutoff) varies in the range of -64–0,
and CC71 (Resonance), CC72 (Release), CC73
(Attack), and CC75 (Decay) vary in the range
of 0–+63.
AFT Aftertouch
BEND DOWN Lowers the pitch.
BEND UP Raises the pitch.
PART FADE1
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
Parameter
[K] [J] button
Value
[-] [+] Buttons
Explanation
Pres
(Pressure Function) PART FADE2
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
CTRL MOD BAR
You can specify whether the CTRL MOD BAR settings follow the
settings of the currently selected program or follow the system
settings.
If the currently selected program’s CTRL MOD BAR: Source
parameter is set to “SYS,” the system settings are used.
Parameter
[K] [J] button
Value
[-] [+] Buttons
Explanation
Func
(Modulation Bar
Function)
Specify the function that is assigned to the modulation bar
when program’s CTRL MOD BAR: Source is set to “SYS.”
OFF No function is assigned.
CC01–31, 32 (OFF),
33–95
Controller number 1–31, 32, 33–95
* CC74 (Cutoff) varies in the range of -64–0,
and CC71 (Resonance), CC72 (Release), CC73
(Attack), and CC75 (Decay) vary in the range
of 0–+63.
AFT Aftertouch
BEND DOWN Lowers the pitch.
BEND UP Raises the pitch.
PART FADE1
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
PART FADE2
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127

Roland AX-EDGE Specifications

General

Brand	Roland
Model	AX-EDGE
Category	Synthesizer
Language	English