EasyManuals Logo

TP-Link TL-SG2216 User Manual

TP-Link TL-SG2216
183 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #92 background imageLoading...
Page #92 background image
it will be added to the
multicast address table with its member port time specified; if the receiving
port is already a member port, its member port time will be directly reset.
3. IGMP Leave Message
The host, running IGMPv1, does not send IGMP leave message when leaving a multicast group,
as a result, the switch can not get the leave information of the host momentarily. However, after
leaving the multicast group, the host does not send IGMP report message any more, so the switch
will remove the port from the corresponding multicast address table when its member port time
times out. The host, running IGMPv2 or IGMPv3, sends IGMP leave message when leaving a
multicast group to inform the multicast router of its leaving.
When receiving IGMP leave message, the switch will forward IGMP group-specific-query message
to check if other members in the multicast group of the port need this multicast and reset the
member port time to the leave time. When the leave time times out, the switch will remove the port
from the corresponding multicast group. If no other member is in the group after the port is
removed, the switch will send IGMP leave message to the router and remove the whole multicast
group.
IGMP Snooping Fundamentals
1. Ports
Router Port: Indicates the switch port directly connected to the multicast router.
Member Port: Indicates a switch port connected to a multicast group member.
2. Timers
Router Port Time: Within the time, if the switch does not receive IGMP query message from the
router port, it will consider this port is not a router port any more. The default value is 300 seconds.
Member Port Time: Within the time, if the switch does not receive IGMP report message from the
member port, it will consider this port is not a member port any more. The default value is 260
seconds.
Leave Time: Indicates the interval between the switch receiving a leave message from a host and
the switch removing the host from the multicast groups. The default value is 1 second.
The IGMP Snooping function can be implemented on Snooping Config, Port Config, VLAN
Config and Multicast VLAN pages.
8.1.1 Snooping Config
To configure the IGMP Snooping on the switch, please firstly configure IGMP global configuration
and related parameters on this page.
If the multicast address of the received multicast data is not in the multicast address table, the
switch will broadcast the data in the VLAN. When Unknown Multicast Discard feature is enabled,
the switch drops the received unknown multicast so as to save the bandwidth and enhance the
process efficiency of the system. Please configure this feature appropriate to your needs.
Choose the menu MulticastIGMP SnoopingSnooping Config to load the following page.
84

Table of Contents

Other manuals for TP-Link TL-SG2216

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TP-Link TL-SG2216 and is the answer not in the manual?

TP-Link TL-SG2216 Specifications

General IconGeneral
Jumbo frames10000
Forwarding rate23.8 Mpps
MAC address table8000 entries
Jumbo frames supportYes
Packet buffer memory4 MB
Supported data transfer rates10/100/1000 Mb/s
10G supportNo
Number of VLANs512
Networking standardsIEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ab, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN featuresMulticast VLAN, Tagged VLAN, Voice VLAN
DHCP featuresDHCP client
Security algorithmsSSH, SSL/TLS
Switch typeManaged
Switch layerL2
Combo SFP ports quantity2
Installed SFP modules quantity0
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity16
Power sourceAC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power supply included-
Form factor1U
CertificationCE, FCC, RoHS
Product colorBlack
Minimum system requirementsMicrosoft® Windows® XP, Vista™ or Windows 7, Windows 8, MAC® OS, NetWare®, UNIX® or Linux.
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)5 - 90 %
Operating relative humidity (H-H)10 - 90 %
Cabling technology10BASE-T/100BASE-TX/1000Base-T
Package depth250 mm
Package width528 mm
Package height80 mm
Package weight2600 g
Weight and Dimensions IconWeight and Dimensions
Depth180 mm
Width440 mm
Height44 mm

Related product manuals