Xerox Phaser 4510 Service Manual

Phaser 4500/4510 Service Manual 6-7
Adjustments and Calibrations
Adjusting Simplex Registration (Margins)
1. Enter Service Diagnostics.
2. Select Engine NVRAM Adjustments, then press the OK button.
3. Select either the process adjustment (Tray [#] Proc Dir) or scan
adjustment (Tray [#] Scan Dir) for the desired tray, then press the OK
button.
4. Use the Up Arrow and Down Arrow buttons to set the new value. Each
increment of change equals 0.5 mm. (The default value is 8.)
Note
In the scan direction, increasing the value moves the image to the
right and decreasing the value moves the image to the left.
In the process direction, increasing the value moves the image toward
the trail edge and decreasing the value moves the image towards the
lead edge.
5. Press the OK button to save the setting.
6. Press the Back button.
7. Select Engine Test Print, then press the OK button.
8. Select Print Test Pattern, then press the OK button to print the Engine
Test Pattern.
9. Check the following measurements on two consecutive test patterns.
10. Repeat steps 1 through 9 until correct measurements are achieved.
11. Perform the Registration (Side-To-Side) test on page 5-9 and the
Registration (Lead Edge-to-Trail Edge) test on page 5-10. Repeat this
adjustment procedure if the results are incorrect.
Distance Measurement
From the lead edge of the paper to the first horizontal
line (measurement A in the figure on page 6-4)
4mm ± 2mm
From the left edge of the paper to the edge of the thick
vertical line (measurement B in the figure on page 6-4)
4mm ± 2.5mm

Xerox Phaser 4510 Specifications

General

Color	Yes
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	8 s
Print speed (black, normal quality, A4/US Letter)	43 ppm
Maximum internal memory	512 MB
Sound power level (standby)	28 dB
Sound pressure level (printing)	56.1 dB
Total input capacity	1350 sheets
Total output capacity	500 sheets
Maximum input capacity	1800 sheets
Maximum number of input trays	2
Multi-Purpose tray input capacity	150 sheets
I/O ports	Parallel (IEEE 1284), USB 2.0
Power supply type	220 V
Weight (imperial)	45.2 lbs
Power consumption (active)	675 W
Acoustic power emissions (active, print, copy or scan)	71.9 dB
Envelopes sizes	B5, C5, DL
Custom media width	76 - 216 mm
Maximum print size	216 x 356 mm
Custom media length	127 - 356 mm
Paper tray media types	Bond paper, Coated paper, Envelopes, Labels, Plain paper, Recycled paper, Transparencies
Paper tray media weight	64 - 216 g/m²
Non-ISO print media sizes	Executive (184 x 267mm), Folio (media size), index card, Letter (media size), Statement (140 x 216mm)
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Wi-Fi	No
Supported network protocols (IPv4)	USB/Parallel, 10/100 Base-TX Ethernet
PCL fonts	81
Printer fonts	PCL, PostScript
Maximum duty cycle	250000 pages per month
Recommended duty cycle	25000 pages per month
Number of PostScript fonts	139
Number of print cartridges	1
Display	LCD
Certification	EMC Directive 89/336/EEC, FCC Part 15, Class B, Low Voltage Directive 73/23/EEC, RoHS 2002/95/EC
Operating temperature (T-T)	41 - 95 °F
Operating relative humidity (H-H)	15 - 85 %
Power consumption (standby)	80 W
Power consumption (PowerSave)	18 W
Package weight	49896 g
Standard interfaces	Ethernet, Parallel, USB 2.0
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.

Weight and Dimensions

Dimensions (WxDxH)	630 x 630 x 1194 mm