941015
BB 10x15
940610
BB 6x10
940509
BB 5x9
A
B
INITIAL POSITION:
PLACE TAB
IN THIS NOTCH
Open Holder
(hole)
FRONT
Closed Holder
(no hole)
DETAIL
DETAIL
30 2032 ALU NUT FOR SUSP. PIVOT PIN (2)
30 2040 LOWER SUSPENSION HOLDER ( SET 2+1+1)
30 2070 ECCENTRIC NYLON HUB FOR BULKHEAD + COVERS (4+2)
30 2074 ECCENTRIC REAR NYLON HUBS 0° & 2°
30 2080 CASTER CLIPS SET 4+3+2+1 MM (2)
30 3159 SHORT SUSPENSION ARM - REAR LOWER - C-HUB
30 5431 HIGH-PERFORMANCE KEVLAR DRIVE BELT FRONT 3 x 507 MM
30 5442 HIGH-PERFORMANCE KEVLAR DRIVE BELT REAR 3 x 180 MM
30 5516 ALU SOLID LAYSHAFT T1FK'05
30 5575 FIXED PULLEY 20T (2)
30 5784 SPUR GEAR 84T / 48
30 5787 SPUR GEAR 87T / 48 (OPTION)
30 5790 SPUR GEAR 90T / 48 (OPTION)
30 7312 REAR WISHBONE PIVOT PIN BOTTOM T1FK'05 - C-HUB (2)
30 9319 UNIVERSAL SET OF PLASTIC SHIMS
94 0509 HIGH-SPEED BALL-BEARING MR95ZZ 5 x 9 x 3 RUBBER COVERED (2)
94 0610 HIGH-SPEED BALL-BEARING MR106ZZ 6 x 10 x 3 RUBBER COVERED (2)
94 1015 HIGH-SPEED BALL-BEARING 10 x 15 x 4 RUBBER COVERED (2)
90 2305 HEX SCREW SH M3x5 (10)
90 2310 HEX SCREW SH M3x10 (10)
90 2312 HEX SCREW SH M3x12 (10)
90 4306 HEX SCREW SFH M3x6 - SILVER (10)
90 1308 HEX SCREW SB M3x8 (10)
90 1408 HEX SCREW SB M4x8 (10)
96 5050 E-CLIP 5 (10)
98 1210 PIN 2x10 (10)
30 1112 6-CELL CHASSIS T1FK'05 - CNC MACHINED
30 2002 ALU SUSP. ADJUSTABLE BULKHEADS T1FK'05 (4)
90 4306 HEX SCREW SFH M3x6 - SILVER (10)
30 5002 BALL DIFF. WITH LABYRINTH COVERS™ - (FACTORY KIT)
2. REAR TRANSMISSION
To tighten rear belt:
Rotate rear nylon hubs in arrow direction (A)
To loosen rear belt:
Rotate rear nylon hubs in arrow direction (B)
To remove holder, press
out with tool as shown.
1. Press the plastic holders for the small ball-bearings into the rear
bulkheads. The flanges on the holders go to the INSIDE of the
bulkheads. The open holder (with hole) goes in the LEFT bulkhead. The
closed holder (no hole) goes in the RIGHT bulkhead.
2. Press a #940610 (BB 6x10) ball-bearing into the OPEN plastic
holder (with hole) in the LEFT bulkhead. Press a #940509 (BB 5x9)
ball bearing into the CLOSED plastic holder (no hole) in the RIGHT
bulkhead.
3. Press oval-shaped differential height adjusters into rear bulkheads,
with large holes near the bottom. The flanges on the adjusters go to the
INSIDE of the bulkheads.
4. Press large eccentric ball-bearing holders into the oval-shaped diff
height adjusters. Align the tab of each holder with the middle notch in
each adjuster as shown.
5. Press #941015 (BB 10x15) ball-bearings into the eccentric holders.
Make sure all bearings turn freely and easily.
BELT TENSION ADJUSTMENT
BAG
02
To Next Page
Loading...
Need help?
General
