Danfoss VLT AutomationDrive FC 302 User Manual

5.4 Wiring Overview for E5h and E6h Enclosed Drives
1
2
(NC)
91 (L1)
92 (L2)
93 (L3)
18 (D IN)
15 mA
200 mA
(U) 96
(PE) 99
0/4-20 mA
03
0 V DC - 10 V DC
0/4–20 mA
02
01
05
04
06
24 V (NPN)
0 V (PNP)
0 V (PNP)
24 V (NPN)
19 (D IN)
24 V (NPN)
0 V (PNP)
24 V
0 V
0 V (PNP)
24 V (NPN)
0 V
24 V
24 V (NPN)
0 V (PNP)
0 V (PNP)
24 V (NPN)
33 (D IN)
32 (D IN)
1
2
ON
A53 U-I (S201)
ON
2
1
A54 U-I (S202)
ON=0–20 mA
OFF=0–10 V
95 (PE)
P 5-00
(R+) 82
(R-) 81
+ - + -
2)
0 V
5 V
S801
21
ON
Switch mode
power supply
ON=Terminated
OFF=Open
(NPN) = Sink
=
=
=
37 (D IN) - option
1)
e30bu149.10
Drive
Control compartment
XD2
Terminal
block
XD2.21
XD2.23
XD2.22
XD2.24
XD2.26
XD2.25
XD2.4
XD2. 5
XD2.2
XD2.3
XD2.1
XD2.19
XD2.17
XD2.16
XD2.15
XD2.14
XD2.18
XD2.13
XD2.12
XD2.11
XD2.10
XD2.9
XD2.8
XD2.7
XD2.6
cabinet
(V) 97
(W) 98
240 V AC, 2A
400 V AC, 2A
240 V AC, 2A
400 V AC, 2A
Brake temp
RS485
(PNP) = Source
(COM RS485) 61
(N RS485) 69
(P RS485) 68
RS485
Interface
OFF-ON
S801/Bus term.
(COM A OUT) 39
(A OUT) 42
10 V DC
24 V DC
3-phase
50 (+10 V OUT)
+10 V DC
power
input
0 V DC - 10 V DC
0/4–20 mA
29 (D IN/OUT)
27 (D IN/OUT)
20 (COM D IN)
13 (+24 V OUT)
12 (+24 V OUT)
55 (COM A IN)
54 (A IN)
53 (A IN)
Motor
Brake
resistor
Relay1
Relay2
Analog output
(R-) 83
Regen+
Regen-
Regen
(option)
(option)
Illustration 21: Basic Wiring Overview for Enclosures E5h and E6h
1
Terminal 37 (optional) is used for Safe Torque Off. Refer to the VLT
®
pFC Series - Safe Torque Off Operating Guide for
installation instructions.
AQ262139143212en-000301 / 130R087954 | Danfoss A/S © 2021.10
Electrical Installation
VLT® AutomationDrive FC 302
Operating Guide

Danfoss VLT AutomationDrive FC 302 Specifications

General

Brand	Danfoss
Model	VLT AutomationDrive FC 302
Category	DC Drives
Language	English