Danfoss VLT AutomationDrive FC 361 Programming Guide

5.2 Parameter Lists
5.2.1 0-** Operation / Display
Para
meter
numb
er
Parameter description Default value 4 set-up Change
during
operation
Conversion
index
Type
0-0* Basic Settings
0-01 Language 0 N/A 1 set-up TRUE – Uint8
0-02 Motor Speed Unit [1] Hz 4 set-ups FALSE – Uint8
0-04 Operating State at Power-up (Hand) [1] Forced stop, ref=old All set-ups TRUE – Uint8
0-1* Set-up Operations
0-10 Active Set-up [1] Set-up 1 1 set-up TRUE – Uint8
0-11 Edit Set-up [1] Set-up 1 All set-ups TRUE – Uint8
0-12 This Set-up Linked to [0] Not linked All set-ups FALSE – Uint8
0-13 Readout: Linked Set-ups 0 N/A All set-ups FALSE 0 Uint16
0-14 Readout: Edit Set-ups / Channel 0 N/A All set-ups TRUE 0 Int32
0-2* LCP Display
0-20 Display Line 1.1 Small 1617 All set-ups TRUE – Uint16
0-21 Display Line 1.2 Small 1614 All set-ups TRUE – Uint16
0-22 Display Line 1.3 Small 1610 All set-ups TRUE – Uint16
0-23 Display Line 2 Large 1613 All set-ups TRUE – Uint16
0-24 Display Line 3 Large 1502 All set-ups TRUE – Uint16
0-25 My Personal Menu ExpressionLimit 1 set-up TRUE 0 Uint16
0-3* LCP Custom Readout
0-30 Unit for User-dened Readout [1] % All set-ups TRUE – Uint8
0-31 Min Value of User-dened Readout 0 CustomReadoutUnit All set-ups TRUE -2 Int32
0-32 Max Value of User-dened Readout 100 CustomReadoutUnit All set-ups TRUE -2 Int32
0-37 Display Text 1 0 N/A 1 set-up TRUE 0 VisStr[25]
0-38 Display Text 2 0 N/A 1 set-up TRUE 0 VisStr[25]
0-39 Display Text 3 0 N/A 1 set-up TRUE 0 VisStr[25]
0-4* LCP Keypad
0-40 [Hand on] Key on LCP [1] Enabled All set-ups TRUE – Uint8
0-41 [O] Key on LCP [1] Enabled All set-ups TRUE – Uint8
0-42 [Auto on] Key on LCP [1] Enabled All set-ups TRUE – Uint8
0-43 [Reset] Key on LCP [1] Enabled All set-ups TRUE – Uint8
0-5* Copy/Save
0-50 LCP Copy [0] No copy All set-ups FALSE – Uint8
0-51 Set-up Copy [0] No copy All set-ups FALSE – Uint8
0-6* Password
0-60 Main Menu Password 100 N/A 1 set-up TRUE 0 Int16
0-61 Access to Main Menu w/o Password [0] Full access 1 set-up TRUE – Uint8
5.2.2 1-** Load and Motor
Param
eter
numb
er
Parameter description Default value 4 set-up Change
during
operation
Conversion
index
Type
1-0* General Settings
1-00 Conguration Mode ExpressionLimit All set-ups TRUE – Uint8
1-01 Motor Control Principle [1] VVC+ All set-ups FALSE – Uint8
1-03 Torque Characteristics [0] Constant torque All set-ups TRUE – Uint8
Parameter Lists VLT® AutomationDrive FC 361
160 Danfoss A/S © 03/2019 All rights reserved. MG06J202
55

Danfoss VLT AutomationDrive FC 361 Specifications

General

Brand	Danfoss
Model	VLT AutomationDrive FC 361
Category	DC Drives
Language	English