Furuno FM-7000 User Manual

FM-8700
E5-2
TEST VHF ch70
manual
System < Rom version >
V P ID DSC RT CH PO L
[SELECT]
[9]
Select "ID" press the [ENT] key.
Select "CH70" or "VHF" press the [ENT] key.
Select "ON" or "OFF" and press the [ENT] key twice.
Select "ON" or "OFF" and press the [ENT] key .
Select "ON" or "OFF" and press the [ENT] key.
Enter own identification
[digits] MMSI: - - - - - - - - -
DSC : Receiver < CH70 >
CH70 [1] VHF [2]
DSC : remote DMC ON
ON [1] OFF [2]
RT1-Mode : USA/WX < OFF >
ON [1] OFF [2]
RT1-Mode : private < OFF >
OFF [1] ON [2]
ON [1] OFF [2]
RT2-Hook work : CH16 < ON >
Enter own ship's ID and the [ENT] key twice.
When two FM-8700s are installed, designate
one as Main (CH70) and the other as Sub (VHF).
The default setting is "CH70" as mainunit.
Select whether DMC-5 is connected or not.
(ON:connected)
Disable or enable the USA/WX mode.
Disable or enable the PRIVATE channel mode.
Select "ON" or "OFF" and press the [ENT] key.
Disable or enable watch on CH16 when handset is on hook.
ON [1] OFF [2]
RT2-Hook work : SP < ON >
Select "ON" or "OFF" and press the [ENT] key .
Disable or enable speaker when handset is on hook.
Select "ON" or "OFF" and press the [ENT] key.
Disable or enable monitoring of external equipment;
For example, Remote Station RB-700 is monitored.
OFF [1] ON [2]
RT3-Time out timer < OFF >
OFF [1] ON [2]
RT4-TX AF monitor < OFF >
Select "ON" or "OFF" and press the [ENT] key .
ON:Automatic setting of 1W when selecting the low output power
channel set by "Channel Preset" operation.
ON [1] OFF [2]
RT5-Auto 1W < ON >
Select "ON" or "OFF" and press the [ENT] key .
Disable or enable dual watch.
ON [1] OFF [2]
RT6-Dual watch < ON >
Select "ON" or "OFF" and press the [ENT] key .
Disable or enable channel scanning.
ON [1] OFF [2]
RT6-Scanning < ON >
Press the [ENT] key 4 times .
Settings auto SQ function (*better not change these value)
LOW:Enter lowest limt of voice frequency which open
automatic SQ. Enter value by the following formula.
Setting value x 50 = Low Frequency
HIGH:Enter highest frequency which opens automatic SQ.
Setting value x 50 = Hi Frequency
HOLD:Enter SQ hold time in two digits, by follwing the formula.
Setting value x 20 msec= Time desired
LOW= 00 HIGH HOLD
RT7-Auto SQ <L00 H03 H030>
ENABLE= TX[1] RX[2] UN[3]
INTL CH:016 < TX SIMP HI >
Select "ON" or "OFF" and press the [ENT] key .
Disable or continue after a long transmission.
For USA, set to ON, Not effective unless USA mode is enabled.
*You had better not change these value.
(*1)
(*1)
(continued next page)
*
2. System settings
2.1 Initial Settings
This section provides how to set-up the following items.
1. Ship’s ID number 4. Channel system settings
2. DSC block settings 5. Selection of LCD display, Japanese or English
3.
VHF block settings 6. Protection (Lock Initial settings)
Protection OFF
Refer to section “2.2Changing
system settings”.
OFF!!
Refer to section “5.Chenging ID
and Private mode”.
Refer to section “5.Changing ID
and Private mode”.

Furuno FM-7000 Specifications

General

Brand	Furuno
Model	FM-7000
Category	Marine Equipment
Language	English