Honeywell CIU 888 User Manual

Getting Started
Part No.: 4417584_Rev12 Configuration Manual
CIU 888 3 - 23
$*6
3.2 Configuring a site using CIU 888 Service Tool
The first step in configuration of CIU 888 is the creation of a site using
CIU 888 Service Tool. After a new site is created, the program prompts
for a set of global settings. Global settings are the overall configuration
settings applicable at a site level, see section 3.2.3 for more details.
Global settings are required for initiating any site configuration.
After the site global settings are entered, CIU 888 Service Tool prompts
for CIU 888 name and then CIU 888 Service Tool creates a site
configuration.
A site gives an overview of the configuration at a specific customer’s
site. The site configuration can be saved offline and opened at a later
point in time. Selecting a site gives you access to its configuration.
When the site is not available in the list, a new site must be created.
3.2.1 Preparation
Before you start configuring CIU 888, certain preparations are
necessary. Make sure the following information is available:
 Site layout
 Field cabling information (which gauges are connected on the
same pair of field wires, etc.)
 Tag names of field devices (gauges, CIU and tanks).
 Tank information (strapping tables, or tank capacity tables, roof
details, etc.)
 Information on the types of stored product
 Host communication setup
 Modbus TCP/IP Communication set up

Honeywell CIU 888 Specifications

General

Brand	Honeywell
Model	CIU 888
Category	Recording Equipment
Language	English

Summary

Chapter 1 Introduction

When to use CIU 888 Service Tool

CIU 888 and Service Tool Compatibility Matrix

Recommended workflows to commission CIU 888

Chapter 2 Installing CIU 888 Service Tool

Prerequisites

Installing CIU 888 Service Tool

Instructions for installing the CIU 888 Service Tool.

Installing CIU 888 Service Tool on the new machine

Detailed steps for installing the service tool on a new machine.

Chapter 3 Getting Started

CIU 888 Web interface

Overview of functionalities and access to the CIU 888 Web interface.

Launching the CIU 888 Web interface

Configuring a site using CIU 888 Service Tool

First step in configuration: creating a site using the Service Tool.

Launching CIU 888 Service Tool

Creating a new site

Procedure for creating a new site configuration in the Service Tool.

CIU 888 Node Properties/Settings

Configuring a Field port

Steps for configuring serial, Ethernet, and TRL/2 field ports.

Configuring a Tank

Procedures for configuring tank settings under serial and Ethernet ports.

Product configuration

Configuring a GPU Data Input or Modbus Data Input or TRL/2 Data Input

Adding data inputs for GPU, Modbus, or TRL/2 devices.

Configuring a Host port

Configuration of serial and Ethernet host ports.

Configuring User defined Modbus map

Creating and managing user-defined Modbus maps.

Configuring Ethernet Host port

Steps for configuring FTE A, FTE B, and LAN ports.

Configuring Modbus map for TCP/IP ports

Creating, deleting, and editing TCP/IP Modbus maps.

Sending Configuration to CIU 888

Process for sending site configuration to the CIU 888.

Generating INI Files

Steps to generate INI files for Entis Pro.

Verifying Configuration

Procedure to verify the current configuration of the CIU 888.

Importing an existing site configuration

Chapter 4 Commissioning of a Standalone System Setup

Running the initial setup of the CIU 888

Performing the initial setup and login for the CIU 888.

Logging on to the CIU 888 and changing the initial password

Procedure for initial login and password change on CIU 888.

Verifying the CIU 888 license

Steps to verify if the CIU 888 license is installed and valid.

OPCUA Certificate Management

OPCUA Self-Signed Certificate Management

Managing self-signed certificates for OPCUA communication.

OPCUA CA-Signed Certificate Management

Managing CA-signed certificates for OPCUA communication.

Chapter 5 Commissioning of a Redundant System Setup

Requirements for commissioning

Running the initial setup of the primary CIU 888

Performing initial setup for the primary CIU 888 in a redundant system.

Setting up the site configuration

Setting up site configuration for primary CIU 888.

Sending the site configuration to the primary CIU 888

Sending the configured site setup to the primary CIU 888.

Commissioning of the secondary CIU 888

Configuring the secondary CIU 888 as a counterpart.

Generating INI files

Verifying the working of the system setup

Chapter 6 Updating CIU 888 Site Configuration

Requirements for updating the non redundant CIU 888 site configuration

Requirements for updating the redundant CIU 888 site configuration

Implementing the required changes in the site configuration

Steps to implement changes in the site configuration.

Sending the site configuration to the CIU 888

Sending updated site configuration to CIU 888.

Generating the INI files

Verifying the working of the CIU 888 system setup

Special Operating Procedure to perform configuration updates on redundant CIU

Procedure for updating configuration on redundant CIU without restart.

Updating configuration for Restart parameters

Updating configuration for Non-Restart parameters

Chapter 7 General CIU 888 Functions

(Re)starting and shutting down the CIU 888

Procedures for starting, restarting, and shutting down the CIU 888.

Restarting the CIU 888

W&M lock key switch and Configuration lock key switch

Appendix A Data Handling

Appendix B Scanning

Appendix C Redundancy

Sync Link and database synchronization

Supported redundant CIU 888 topologies of deployment

RS-232 host port redundancy with redundant CIU 888s and host port redundancy on demand of host system

RS-232 host port redundancy with redundant CIU 888s and data synchronization between host systems

Modbus TCP host port redundancy with redundant CIU 888s and data synchronization between host systems

Redundant CIU 888-Experion PKS Integration

Configuration steps for integrating redundant CIU 888 with Experion PKS.

Configuring CIU 888

Configuring Experion PKS

Steps for required Experion PKS configuration using Quick Builder.

Configure Modbus Points

Configure Points for CIU 888 parameters

Appendix H Creation of new Modbus field device / TRL/2 Field Device Configuration File