HP 5120 EI Switch Series User Manual

162
To do…
Use the command…
Remarks
Enter system view
system-view
—
Create a user profile, and enter its
view
user-profile profile-name
Required
You can use the command to
enter the view of an existing user
profile.
Configuring a user profile
After a user profile is created, apply a QoS policy in user profile view to implement restrictions on online
users. The QoS policy takes effect when the user profile is enabled and a user using the user profile goes
online.
Follow these steps to configure user profile:
To do…
Use the command…
Remarks
Enter system view
system-view
—
Enter user profile view
user-profile profile-name
Required
Apply the QoS policy
qos apply policy policy-name
{ inbound | outbound }
Required
The inbound keyword applies the QoS policy to
incoming traffic of the switch (traffic sent by
online users). The outbound keyword applies the
QoS policy to outgoing traffic of the switch
(traffic sent to online users).
NOTE:
 If a user profile is enabled but not used by any online user, you can edit only the content of the ACL that is
referenced by the QoS policy in the profile. If the user profile is being used by online users, you cannot edit any
configuration in the QoS policy.
 The QoS policies that can be applied to user profiles support only the remark, car, and filter actions.
 Do not apply an empty policy in user profile view because a user profile with an empty policy applied cannot be
enabled.
Enabling a user profile
Enable a user profile so that configurations in the profile can be applied by the device to restrict user
behaviors. If the device detects that the user profile is disabled, the device denies the associated user
even the user has been verified by the authentication server.
Follow these steps to enable a user profile:
To do…
Use the command…
Remarks
Enter system view
system-view
—
Enable a user profile
user-profile profile-name enable
Required
A user profile is disabled by
default.

HP 5120 EI Switch Series Specifications

General

Model	HP 5120 EI Switch Series
Layer	Layer 3
Forwarding Rate	96 Mpps
MAC Address Table Size	16K
Power Supply	Internal
Management	CLI, Web GUI, SNMP
Features	IPv6 support
Routing Protocol	RIP, OSPF, BGP
Security Features	ACLs
Layer 3 Features	OSPF, BGP, VRRP
Redundancy	VRRP
Operating Temperature	0°C to 45°C
SFP Slots	4
VLAN Support	4094
Jumbo Frames	9216 bytes

Summary

AAA Configuration

RADIUS Protocol

HWTACACS Protocol

AAA Configuration Considerations and Task List

Outlines the tasks and considerations required for configuring AAA on a NAS device.

Configuring AAA Schemes

Details the process of configuring AAA schemes, including local, RADIUS, and HWTACACS schemes.

Configuring Local Users and Groups

Configuring RADIUS and HWTACACS Schemes

Describes configuring RADIUS and HWTACACS schemes, specifying servers, shared keys, and parameters.

Configuring AAA Methods for ISP Domains

Configuring AAA Authentication, Authorization, and Accounting Methods

Details the configuration of authentication, authorization, and accounting methods for users within an ISP domain.

802.1X Configuration

Configuring 802.1X

Provides steps for enabling 802.1X, setting access control, and configuring guest/Auth-Fail VLANs.

Enabling 802.1X and Access Control

Details enabling 802.1X globally and on ports, along with specifying access control methods.

MAC Authentication Configuration

MAC Authentication Configuration Task List

Lists tasks for configuring MAC authentication, including basic setup and examples.

Basic Configuration for MAC Authentication

Covers the basic steps for configuring MAC authentication globally and on ports.

MAC Authentication Configuration Examples

Portal Configuration

Configuring Layer 2 Portal Authentication

Details the steps to configure Layer 2 portal authentication, including VLAN assignment and Auth-Fail VLAN.

Portal Configuration Examples

Triple Authentication Configuration

Configuring Triple Authentication

Provides steps to configure triple authentication by enabling portal, MAC, and 802.1X authentication.

Triple Authentication Configuration Examples

Port Security Configuration

Port Security Features and Modes

Enabling Port Security and Setting Mode

Provides steps to enable port security and set its mode, like autoLearn or secure.

User Profile Configuration

User Profile Configuration Task List

Creating and Enabling User Profiles

Details creating and enabling user profiles to apply configurations and restrict user behaviors.

Password Control Configuration

Password Control Configuration Task List

Lists tasks for configuring password control, including global, group, and local user settings.

Configuring Password Control

Details enabling password control features like aging, history, and complexity checking.

Password Control Configuration Example

Public Key Configuration

Configuring the Local Asymmetric Key Pair

Details creating, destroying, displaying, and exporting local RSA or DSA key pairs.

Configuring a Peer Public Key

PKI Configuration

PKI Configuration Task List

Lists tasks for configuring PKI, including entity DN, PKI domain, and certificate requests.

Configuring an Entity DN and PKI Domain

Details configuring entity DN parameters and PKI domains for certificate requests.

Submitting and Retrieving Certificates

Explains submitting certificate requests in auto/manual modes and retrieving certificates.

Configuring PKI Certificate Verification

SSH2.0 Configuration

Configuring the Device as an SSH Server

Provides steps to configure the device as an SSH server, including key generation and user setup.

SSH Server Configuration Task List

Lists tasks for configuring the SSH server, such as key pair generation and enabling the server.

Configuring the Device as an SSH Client

Details configuring the device as an SSH client, including source IP and connection setup.

SSH Client Configuration Examples

SFTP Configuration

Configuring the Device as an SFTP Server

Provides steps to enable and configure the device as an SFTP server.

Configuring the Device an SFTP Client

Details configuring the device as an SFTP client, including source IP and connection setup.

SFTP Client Configuration Example

SFTP Server Configuration Example

SSL Configuration

SSL Configuration Task List

Configuring an SSL Server Policy

Details setting SSL parameters for a server, including PKI domain and cipher suites.

Configuring an SSL Client Policy

TCP Attack Protection Configuration

Enabling the SYN Cookie Feature

IP Source Guard Configuration

Static IP Source Guard Binding

Dynamic IP Source Guard Binding

Configuring IPv4 Source Guard Binding

Configuring IPv6 Source Guard Binding

ARP Attack Protection Configuration

ARP Attack Protection Configuration Task List

Configuring ARP Defense Against IP Packet Attacks

Configuring ARP Detection

ND Attack Defense Configuration

Enabling Source MAC Consistency Check for ND Packets

Configuring the ND Detection Function