EasyManuals Logo
Home>HP>Tablet>Elite x2 1011 G1

HP Elite x2 1011 G1 Maintenance And Service Guide

HP Elite x2 1011 G1
155 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #111 background imageLoading...
Page #111 background image
BIOS installation procedures vary. Follow any instructions that are revealed on the screen after the download
is complete. If no instructions are revealed, follow these steps:
1. From the Start screen, type file, and then select File Explorer.
2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.
Using MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is
enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices
contain bootable media or files that the computer needs to start and operate properly.
NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot
order.
You can change the order in which the computer searches for a boot device by changing the boot order in
Computer Setup. You can also press esc while the “Press the ESC key for Startup Menu” message is displayed
at the bottom of the screen, and then press f9. Pressing f9 displays a menu that shows the current boot
devices and allows you to select a boot device. Or, you can use MultiBoot Express to set the computer to
prompt you for a boot location each time the computer turns on or restarts.
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
To set a new boot order that the computer uses each time it is turned on, by changing the boot order in
Computer Setup.
To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options
menu.
To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device each
time the computer is turned on or restarted.
Setting a new boot order in Computer Setup
To start Computer Setup and set a boot device order that the computer uses each time it is turned on or
restarted, follow these steps:
Using MultiBoot 101

Table of Contents

Other manuals for HP Elite x2 1011 G1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP Elite x2 1011 G1 and is the answer not in the manual?

HP Elite x2 1011 G1 Specifications

General IconGeneral
SteppingF0
Tjunction95 °C
Processor codeSR23L
Processor cache4 MB
Processor cores2
System bus rate- GT/s
Processor familyIntel® Core™ M
Processor seriesIntel Core M-5Y Mobile series
Processor threads4
Processor codenameBroadwell
Processor frequency1.1 GHz
Processor cache typeL3
Processor manufacturerIntel
Processor package size30 x 16.5 mm
Conflict-Free processorYes
Processor front side bus- MHz
Processor boost frequency2.6 GHz
Processor operating modes32-bit, 64-bit
Graphics & IMC lithography14 nm
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Thermal Design Power (TDP)4.5 W
Scenario Design Power (SDP)3.5 W
Configurable TDP-down frequency0.6 GHz
Internal memory8 GB
Memory clock speed1600 MHz
Internal memory typeDDR3L-SDRAM
Storage mediaSSD
Compatible memory cardsMicroSD (TransFlash)
Internal storage capacity256 GB
Display diagonal11.6 \
Touch technologyMulti-touch
Graphics cardHD Graphics 5300
Rear camera typeSingle camera
Rear camera resolution (numeric)5 MP
Front camera resolution (numeric)2 MP
Processor ARK ID84669
Processor socketBGA 1234
Wi-Fi standards802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version4.0
Top Wi-Fi standardWi-Fi 5 (802.11ac)
Near Field Communication (NFC)-
Microphone inNo
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Country of originChina
Device typeTablet PC
Form factorSlate
Product colorBlack, Silver
Intel Identity Protection Technology version1.00
Intel Stable Image Platform Program (SIPP) version0.00
Battery capacity- mAh
Battery life (max)9 h
PlatformWindows
Operating system installedWindows 8.1 Pro
Weight and Dimensions IconWeight and Dimensions
Depth192.7 mm
Width298 mm
Height10.7 mm
Weight780 g

Related product manuals