65
En
■ 2ch Source
With this setting, you can specify the listening mode
used when 2-channel (2/0) stereo digital sources, such
as Dolby Digital or DTS, are played.
■ Dolby D/Dolby D Plus/TrueHD
With this setting, you can specify the listening mode
used when Dolby Digital or Dolby Digital Plus format
digital audio signals are played (DVD, etc.). Specifies
the default listening mode for Dolby TrueHD sources,
such as Blu-ray or HD DVD (input via HDMI).
■ DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode
used when DTS or DTS-HD High Resolution format
digital audio signals are played (DVD, LD, CD, etc.).
Specifies the default listening mode for DTS-HD
Master Audio sources, such as Blu-ray or HD DVD
(input via HDMI).
■ Other Multich Source
Specifies the default listening mode for multichannel
PCM sources from HDMI IN such as DVD-Audio, and
DSD multichannel sources such as Super Audio CD.
Main menu Miscellaneous
Volume Setup
■ Volume Display
` Absolute
:
Displayed range is Min, 0.5 to 99.5, Max.
` Relative(THX):
Displayed range is –QdB, –81.5dB to +18.0dB.
With this setting, you can choose how the volume level is
displayed.
The absolute value 82 is equivalent to the relative value
0dB.
Note
• If the absolute value is set to 82, “82Ref” will appear on the
display and the THX indicator will flash.
■ Muting Level
` –
QdB (fully muted), –50dB to –10dB in 10 dB steps.
This setting determines how much the output is muted
when the muting function is used (➔ page 46).
■ Maximum Volume
` Off
, 50 to 99 (Absolute display)
` Off
, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”.
■ Power On Volume
` Last
, Min, 1 to 99 or Max (Absolute display)
` Last
, –QdB, –81dB to +18dB (Relative display)
With this preference, you can specify the volume setting
to be used each time the AV controller is turned on.
To use the same volume level that was used when the AV
controller was turned off, select “Last”.
The “Power On Volume” cannot be set higher than the
“Maximum Volume” setting.
■ Headphone Level
` –12dB to 0dB
to +12dB
With this preference, you can specify the headphone
volume relative to the main volume. This is useful if
there’s a volume difference between your speakers and
your headphones.
OSD Setup
■ On Screen Display
` On
` Off
This preference determines whether operation details are
displayed on-screen when an AV controller function is
adjusted.
Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
■ Language
(North American models)
` English
, Deutsch, Français, Español, Italiano,
Nederlands, Svenska
(Australian models)
` English
, Deutsch, Français, Español, Italiano,
Nederlands, Svenska, 中文
This setting determines the language used for the on-
screen setup menus.
12V Trigger A/B/C Setup
Depending on their type, when some components are
turned by using triggers A, B, and C, a large amount of
current may be drawn at once. To prevent this, you can
delay each trigger signal individually. Another application
of trigger delay is to eliminate the “thump” noise that’s
sometimes heard when a source component is turned on.
You can accomplish this by delaying the trigger signal for
your power amplifier, so that it’s the last component to be
turned on.
■ Delay
` 0sec, 1sec, 2sec, 3sec:
When “0sec” is selected, the trigger signal is
activated as soon as the input source is changed.
Note
• By default, “12V Trigger A Setup” is set to “0sec”, “12V
Trigger B Setup” to “1sec”, and “12V Trigger C Setup” to
“2sec”.
• Use a miniplug cable to connect the AV controller’s 12V
TRIGGER OUT A, B, or C jack to the 12 V trigger input of a
connected component.
Miscellaneous
To Next Page
Loading...
Need help?
General
