78
En
■ Status Messages
If either of the following messages is not displayed on the
AV controller’s display, check the connection to your
iPod/iPhone.
• PORT Reading
The AV controller is checking the connection with the
dock.
• PORT Not Support
The AV controller do not support the connected dock.
•PORT UP-A1
UP-A1 Dock is connected.
Note
• The AV controller displays the message “UP-A1” for several
seconds after recognizing the UP-A1.
RI Dock
With the RI Dock, you can easily play the music stored on
your Apple iPod/iPhone through the AV controller and
enjoy great sound, and watch iPod/iPhone slideshows and
videos on your TV. In addition, the onscreen display
(OSD) allows you to view, navigate, and select your
iPod/iPhone model’s contents on your TV, and with the
supplied remote controller, you can control your
iPod/iPhone from the comfort of your sofa. You can even
use the AV controller’s remote controller to operate your
iPod/iPhone.
Note
• Enter the appropriate remote control code before using the AV
controller’s remote controller for the first time (➔ page 81).
• Connect the RI Dock to the AV controller with an u cable
(➔ page 23).
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• Set the AV controller’s Input Display to “DOCK”
(➔ page 45).
■ System Function
Auto Power On
If you press the remote controller’s 1 (Playback)
while the AV controller is on standby, the AV controller
will automatically turn on, select your iPod/iPhone as
the input source, and your iPod/iPhone will start
playback.
Direct Change
If you start iPod/iPhone playback while listening to
another input source, the AV controller will
automatically switch to the input to which the RI Dock
is connected.
Other Remote Operations
You can use the remote controller that came with the
AV controller to control other iPod/iPhone functions.
The available functionality depends on the AV
controller.
iPod/iPhone Alarm
If you use the Alarm function on your iPod/iPhone to
start playback, the AV controller will turn on at the
specified time and select your iPod/iPhone as the input
source automatically.
System Off
When you turn off the AV controller, RI Dock turns off
automatically.
Note
• Linked operations do not work with video playback or when the
alarm is set to play a sound.
• If you use your iPod/iPhone with any other accessories,
iPod/iPhone playback detection may not work.
• This function works only in Standard mode (➔ page 79).
Note
• On the iPod with video and iPod nano (1st generation), the click
wheel is disabled during playback.
By pressing the Remote Mode that’s been programmed
with the remote control code for your Dock, you can
control your iPod/iPhone in the Dock with the buttons
described further in this section.
See “Entering Remote Control Codes” for details on
entering a remote control code (➔ page 81).
See the Dock’s instruction manual for more information.
UP-A1 Dock
Port is preprogrammed with the remote control code for
controlling a Dock via Universal Port.
You can control your iPod/iPhone when “Port” is
selected as the input source.
RI Dock
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• 8Source may not work with a remote control code
(without u). In this case, make an u connection and
enter the remote control code 81993 (with u).
■ With the RI Control
Make an u connection and enter the remote
control code 81993 (with u).
• Set the AV controller’s Input Display to “DOCK”
(➔ page 45).
■ Without the RI Control
You must enter the remote control code 82990 first
(➔ page 82).
■ Operating Notes
• Use the AV controller’s volume control to adjust the playback
volume.
• While your iPod/iPhone is inserted in the RI Dock, its volume
control has no effect.
• If you do adjust the volume control on your iPod/iPhone while
it’s inserted in the RI Dock, be careful that it’s not set too loud
before you reconnect your headphones.
Controlling Your iPod/iPhone
To Next Page
Loading...
Need help?
General
