Intel BX80562QX6700 - Core 2 Extreme 2.66 GHz Processor User Manual

Electrical Specifications
18 Datasheet
2.5.2 DC Voltage and Current Specification
Table 4. Voltage and Current Specifications
Symbol Parameter Min Typ Max Unit Notes
1, 2
NOTES:
1. Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical data.
These specifications will be updated with characterized data from silicon measurements at a later date.
2. Adherence to the voltage specifications for the processor are required to ensure reliable processor operation.
VID Range VID 0.8500 — 1.5 V
3
3. Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and can not be altered. Individual maximum VID values are calibrated during manufacturing such
that two processors at the same frequency may have different settings within the VID range. Note this differs
from the VID employed by the processor during a power management event (Thermal Monitor 2, Enhanced Intel
SpeedStep
®
Technology, or Extended HALT State).
V
CC
Processor Number
QX6850
QX6800
QX6700
Q6700
Q6600
V
CC
for
775_VR_CONFIG_05
3.00 GHz
2.93 GHz
2.66 GHz
2.66 GHz
2.40 GHz
Refer to Table 5 and
Figure 1
V
4, 5, 6
4. These voltages are targets only. A variable voltage source should exist on systems in the event that a different
voltage is required. See
Section 2.3 and Table 2 for more information.
5. The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE lands at the socket
with a 100 MHz bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from the
system is not coupled into the oscilloscope probe.
6. Refer to Table 5 and Figure 1 for the minimum, typical, and maximum V
CC
allowed for a given current. The
processor should not be subjected to any V
CC
and I
CC
combination wherein V
CC
exceeds V
CC_MAX
for a given
current.
V
CC_BOOT
Default V
CC
voltage for initial power up — 1.10 — V
V
CCPLL
PLL V
CC
- 5% 1.50 + 5%
I
CC
Processor Number
QX6850
QX6800
QX6700
Q6600
7
7. These processors have CPUID = 06F7h
I
CC
for
775_VR_CONFIG_05B
3.00 GHz
2.93 GHz
2.66 GHz
2.40 GHz
——
125
125
125
115
A
8
Processor Number
Q6700
Q6600
9
I
CC
for
775_VR_CONFIG_05A
2.66 GHz
2.40 GHz
115
115
8
I
TCC
I
CC
TCC active — — I
CC
A
10
V
TT
FSB termination voltage
(DC + AC specifications)
1.14 1.20 1.26 V
11, 12
VTT_OUT_LEFT
and
VTT_OUT_RIGHT
I
CC
DC Current that may be drawn from
VTT_OUT_LEFT and VTT_OUT_RIGHT per pin
— — 580 mA
I
TT
I
CC
for V
TT
supply before V
CC
stable
I
CC
for V
TT
supply after V
CC
stable
——
8.0
7.0
A
13
I
CC_VCCPLL
I
CC
for PLL land — — 130 mA
I
CC_GTLREF
I
CC
for GTLREF — -— 200 μA

Intel BX80562QX6700 - Core 2 Extreme 2.66 GHz Processor Specifications

General

Brand	Intel
Model	BX80562QX6700 - Core 2 Extreme 2.66 GHz Processor
Category	Computer Hardware
Language	English