Lightware UMX-OPT-TX150R User Manual

Page 88 / 107 Section 10. Programmers reference
10.8.4. Query analog timing properties
Description: Check analog timing data of the input ports.
Format
Example
Command
{:ANALOG#<in>@<S/A>I=?}
→
{:analog#2@si=?}
Response
(ANALOG#<in>@<S/A>I=
<PHS>;<FHS>;
<HS>;<VS>;
<HP>;<VP>;<LCF>;
<FORM>;<VSP>;<HSP>;<FPS>)CrLf
←
(ANALOG#2@SI=
0;2160;
1600;1200;
455;41;1242;
P;+;+;60;)CrLf
Legend: Please read section 10.8.3 on page 87.
10.8.5. Reset analog timing properties
Description: This command resets the analog timing properties.
Format
Example
Command
{:ANALOG#<in>@<S/A>I=RESET}
→
{:analog#2@si=reset}
Response
(ANALOG#<in>@<S/A>I=
<PHS>;<FHS>;
<HS>;<VS>;
<HP>;<VP>;<LCF>;
<FORM>;<VSP>;<HSP>;<FPS>)CrLf
←
(ANALOG#1@SI=
0;2160;
1600;1200;
455;41;1242;
P;+;+;60;)CrLf
Legend: Please read section 10.8.3 on page 87.
10.8.6. Set analog color properties
Description: Set analog color properties data of the input ports.
Format
Example
Command
{:PICTURE#<in>@<S/A>I=
<DF_CHA>;<DF_CHB>;<DF_CHC>;
<G_CHA>;<G_CHB>;<G_CHC>;
<O_CHA>;<O_CHB>;<O_CHC>;
<CONT>;<SAT>;<BRIGHT>;<HUE>;)
→
{:picture#2@si=
1023;1023;1023;
1023;1023;1023;
1023;1023;1023;
128;128;0;0;)CrLf
Response
(PICTURE#<in>@<S/A>I=
<DF_CHA>;<DF_CHB>;<DF_CHC>;
<G_CHA>;<G_CHB>;<G_CHC>;
<O_CHA>;<O_CHB>;<O_CHC>;
<CONT>;<SAT>;<BRIGHT>;<HUE>;)CrLf
←
(PICTURE#2@SI=
1023;1023;1023;
1023;1023;1023;
1023;1023;1023;
128;128;0;0;)CrLf
Legend: <S/A>: Affected ports:
S = single selected input
A = all inputs
<DF_CHA> Digital fine-clamp for CH-A:
0-4096
<DF_CHB> Digital fine-clamp for CH-B:
0-4095
<DF_CHC> Digital fine-clamp for CH-C:
0-4095
<G_CHA> Gain for CH-A:
0-1023
<G_CHB> Gain for CH-B:
0-1023
<G_CHC> Gain for CH-C:
0-1023
<O_CHA> Offset for CH-A:
0-1023
<O_CHB> Offset for CH-B:
0-1023
<O_CHC> Offset for CH-C:

Lightware UMX-OPT-TX150R Specifications

General

Product Category	Extender
Model	UMX-OPT-TX150R
Signal Type	HDMI
Input Ports	1
Output Ports	1
Max Resolution	4K@60Hz
Max Distance	150m
HDCP	2.2
Power Supply	5V DC
Operating Temperature	0°C to +40°C
Storage Temperature	-20°C - +70°C

Summary

Safety and Compliance

Safety, Disposal, and Laser Warnings

Crucial safety guidelines, disposal, and laser hazard warnings for proper operation.

Controls and Connections

Front Panel Controls and Indicators

Identifies and describes the DVI-I, VGA, HDMI, Audio, S/PDIF inputs, and status LEDs on the front panel.

Rear Panel Connectors and Controls

Details SC MM OUT, RS-232, USB, Baud Rate, EDID Rotary, Learn, Reset, Status LEDs, and DC 5V IN.

Electrical Input/Output Connections

Explains HDMI, VGA, DVI-I, Digital Audio, RS-232, Fiber Optical, USB, and Analog Audio connections.

Installation and Operation

Operation Modes and Boot Up Sequence

Device Functions and Settings

LED Status Indicators

Input Selection and Autoselect Modes

EDID Memory Management

Service Menu and Remote Control

Remote Control Interfaces

Details control via USB and Serial (RS-232) ports, including simultaneous connections.

Software Control with Matrix Controller

Matrix Controller Software Setup

Provides instructions for installing and establishing a connection with the Lightware Matrix Controller software.

Matrix Controller Menu Operations

Explains the crosspoint array, switching, working modes, input/output parameter settings, and EDID management via software.

Programmers Reference

Device Status and System Commands

EDID Router and Control Commands

Input/Output Property Commands

Maintenance and Troubleshooting

Basic Troubleshooting

Offers solutions for common problems like power, connection, picture distortion, EDID, and HDCP issues.

Specifications

Input/Output and Signal Specifications

Describes supported audio/video inputs, optical output, digital video signal standards, and resolutions.

Supported Resolutions and Cable Distances