EasyManuals Logo
Home>mycom>Air Compressor>SCV Series

mycom SCV Series User Manual

mycom SCV Series
161 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
2205Q2JE-HO-S6-N_2020.01.
Chapter 2 Compressor Specifications and Structure
SCV-series Screw Compressors 2.2 Model designation of the Compressor
2-2
2.2 Model Designation of the Compressor
The meaning of the type designation, which is engraved on the MODEL column of the compressor
nameplate, is as follows.
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
N
200
V
L
D
-
H
[1] When there is specification, working fluid is shown by the symbol. This symbol may not be indicated.
(Example: N= Ammonia, F=Hydro Fluoro Carbon, P: Propane)
[2] Means rotor diameter which is 160, 200, 250 or 320.
[3] Means the specifications of the rotor length which is S, M, L or LL (for rotor diameter 250 only).
[4] Means gas discharge direction which is D (sideways) or G (down: except for rotor diameter 320).
[5] Means the specifications of the slide valve, which is D (grooved type) or Z (low Vi type) as special
specifications. When using standard slide valve, symbol is not added and left justified.
[6] When using the short cut rotors, add the symbol "S". When using the standard rotors, symbol is not
added and left justified.
[7]
When the compressor is standard specifications (standard slide valve, H-port, standard compression
ratio, with economizer port and with liquid injection port) without symbols [8] to [10], this symbol is
not indicated, either.
[8]
This symbol is indicated only when specified by the order. This symbol means a discharge port
which is H (Vi=5.8, with gorooveless standard slide valve), M (Vi=3.65, with gorooveless
standard slide valve), MS (Vi=2.63 equivalent, with grooved slide valve), HS (Vi=1.8, with low
Vi slide valve), or MS (Vi=1.3, with low Vi slide valve).
Note: In the case of following specifications set of discharge port and slide valve, variable Vi
slide valve should be adjusted the first character of this symbol (left side to
"S").
Note: If the evaporating temperature of the system exceeds 0 °C under the L port condition,
select a grooved slide valve for the compressor.
In addition, note that grooved slide valve is available to even less than 0
°C evaporating
temperature under the L port condition.
[9] When the compressor is booster specifications, the symbol "B" is added. When the compressor is
standard specifications, symbol is not added and left justified.
[10] This symbol is indicated only when specified by the order. This symbol indicates if there is
economizer port or/and liquid injection port or not. When this symbol is not indicated, both ports
are provided and symbol may be added as “X”.
Symbol
Economizer port
Liquid injection port
E
with port
no port
I
no port
with port
X
with port
with port
N
no port
no port
The meanings of symbols [8] to [10] are shown below as examples.
200VLD: Discharge port is H port. With economizer and liquid injection ports both.
N200VID-MX: Discharge port is M port. With economizer and liquid injection ports both.
N200VLD-MBX: Discharge port is M port. Booster type, with economizer and liquid injection ports both.
N200VLD-HE: Discharge port is H. With economizer port, without liquid injection port
N200VLD-HN: Discharge port is H. Without economizer and liquid injection ports both.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the mycom SCV Series and is the answer not in the manual?

mycom SCV Series Specifications

General IconGeneral
Brandmycom
ModelSCV Series
CategoryAir Compressor
LanguageEnglish

Related product manuals