Panasonic TH-65EQ1W User Manual

59
English
[Changing delay]
Sets the delay time until the input is switched when
[Power management mode] is [Input detection].
[Off]:
Switches the input if a signal is interrupted even for
a very short period.
1 to 10:
Sets the delay time (sec.). Switches the input when
the set time has elapsed after detecting no signal
is present. However, if the detection period during
which no signal is present is shorter than the set
delay time, the input is not switched.
Note
●
The operation when [Input detection] is selected is the
same as the operation when [Input search] is set to
[Input detection]. (see page 52)
Audio input select
[Audio input select] - submenu screen
HDMI1
HDMI2
DVI-D
PC
VIDEO AV IN
HDMI2
HDMI1
Audio input select
AUDIO IN
AUDIO IN
●
The illustration above shows the factory settings.
Video input Audio input
HDMI1
HDMI1 / AV IN / AUDIO IN /
No audio
HDMI2
HDMI2 / AV IN / AUDIO IN /
No audio
DVI-D / PC
*
/
VIDEO
AV IN / AUDIO IN / No audio
●
No audio: No audio input (Mute)
*
: [PC] may be displayed as [PC[YP
BPR]] depending on
the settings of [PC input mode]. (see page 75)
When the setting for the audio input has been
changed from the factory settings, the audio input is
displayed as below.
HDMI1
Full
AV IN
HDMI-CEC settings
Set for HDMI-CEC function.
For details of HDMI-CEC function, refer to “Using HDMI-
CEC function”. (see page 109)
[HDMI-CEC settings] - submenu screen
1
HDMI-CEC settings
HDMI-CEC control Enable
Disable
HDMI2
----
----
HDMI-CEC operation
MENU code
HDMI1
Display→Device
Disable
Device→Display
Link function
■ [HDMI-CEC control]
Enables/Disables the HDMI-CEC function.
[Disable]: Disables HDMI-CEC control.
[Enable]: Enables HDMI-CEC control.
Note
●
Set to [Enable] to operate HDMI-CEC compatible
device with remote control of the unit.
■ [HDMI1]
Displays the device to operate when HDMI-CEC
compatible device is connected to HDMI 1 terminal.
The control subject can be changed with
.
Note
●
When there is no connected device, [----] will be
displayed.
■ [HDMI2]
Displays the device to operate when HDMI-CEC
compatible device is connected to HDMI 2 terminal.
The control subject can be changed with
.
Note
●
When there is no connected device, [----] will be
displayed.
■ [HDMI-CEC operation]
Displays the operation screen of the HDMI-CEC
compatible device.
Press <RETURN> to hide the operation screen.
■ [MENU code]
Changes the code to assign for the [MENU] operation
on the HDMI-CEC operation screen.
Adjust the code to that of the connected HDMI-CEC
compatible device.

Panasonic TH-65EQ1W Specifications

General

Response time	8 ms
Display diagonal	65 \
Display brightness	350 cd/m²
Display technology	VA
Native aspect ratio	16:9
LED backlighting type	Direct-LED
Contrast ratio (dynamic)	50000:1
Contrast ratio (typical)	4000:1
Display number of colors	1.06 billion colors
Display diagonal (metric)	163.9 cm
Active display area (W x H)	1428 x 803 mm
DisplayPorts quantity	-
Ethernet LAN data rates	10, 100, 1000 Mbit/s
VGA (D-Sub) input ports	1
RMS rated power	20 W
Orientation	Horizontal/Vertical
Product color	Black
Product design	Digital signage flat panel
Bezel width (side)	13.5 mm
Placement supported	Indoor
Bezel width (bottom)	14.5 mm
Panel mounting interface	400 x 400 mm
Purpose	Universal
HDCP version	2.2
Operating hours (hours/days)	18/7
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (off)	0.3 W
Power consumption (standby)	0.5 W
Power consumption (typical)	185 W
Package depth	280 mm
Package width	1655 mm
Package height	1078 mm
Package weight	38000 g
Cables included	AC
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	82 mm
Width	1459 mm
Height	835 mm
Weight	27000 g