Pioneer SC-LX78 User Manual

87
Using other functions
09
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
Set MULTI-ZONE to MULTI ZONE OFF.
! Disconnect the iPod and USB memory device from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI Setup on page 75 ).
1 Switch the receiver into standby.
2 While holding down ENTER on the front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET k/l, then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
! Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting Default
Digital Video Converter
OFF
SPEAKERS
TMd/FW ON
Speaker System
7.2.2ch TMd/FW
Speaker Setting
Front
SMALL
Center
SMALL
TMd/TFw/TBw
SMALL
FH/FW
SMALL
Surr
SMALL
SB
SMALLx2
SW
SW1+2 YES
Surround Position
ON SIDE
Crossover
80Hz
X-Curve
OFF
DIMMER Brightest
Inputs
See Input function default and possible settings on page 52 .
Input Volume Absorber All Inputs
0dB
HDMI
HDMI Audio
AMP
Control
OFF
Control Mode --- (OFF)
ARC (Audio Return Channel) --- (OFF)
PQLS --- (AUTO)
Standby Through
OFF
4K/60p
4:4:4
DSP
Power On Level
LAST
Setting Default
Volume Limit
OFF
Mute Level
FULL
Phase Control
ON
Auto Sound Retriever
iPod/USB, INTERNET RADIO, MEDIA
SERVER, FAVORITES, ADAPTER PORT
input function
ON
Other input functions
OFF
Sound Delay 0 ms
Dual Mono
CH1
DRC
AUTO
LFE Attenuate
0dB
Auto delay
OFF
Digital Safety
OFF
Effect Level ALC (Auto Level Control)
50
Neo:X Options Center Gain
Neo:X CINEMA: 1.0
Neo:X MUSIC: 0.3
Neo:X GAME: 1.0
All Inputs
Listening Mode (2 ch/multi ch)
AUTO SURROUND
Listening Mode (Headphones)
STEREO
See also Setting the Audio options on page 79 for other default DSP settings.
MCACC
MCACC Position Memory
M1. MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance (M1 to M6) 3.00 m
Standing Wave (M1 to M6)
ATT of all channels/filters 0.0 dB
SWch Wide Trim 0.0 dB
EQ Data (M1 to M6)
All channels/bands 0.0 dB
EQ Wide Trim 0.0 dB
Network
Network Standby
OFF
DHCP
ON

Pioneer SC-LX78 Specifications

General

Receiver type	Surround
Speaker selector	A+B
Input sensitivity	400 mV
4Ω speaker support	Yes
Audio output channels	9.2 channels
Audio A/D Converter (ADC)	24-bit/192kHz
Signal-to-Noise Ratio (SNR)	103 dB
Total Harmonic Distortion (THD)	1 %
Power output per channel (1KHz@6 Ohm)	210 W
Power output per channel (20-20KHz@8 Ohm)	250 W
HDMI in	8
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Number of HDMI outputs	3
Multichannel audio output type	Terminals
Speakers connectivity type	-
Audio formats supported	AAC, AIFF, FLAC, M4A, MP3, WAV, WMA
Supported radio bands	AM, FM
Preset stations quantity	63
Optical drive included	No
Supported video modes	1080i, 1080p, 480p, 720p
Product color	Black
Audio decoders	Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS Neo:X, DTS-ES, DTS-HD Master Audio
Volume control	Rotary
Apple docking compatibility	Not supported
On Screen Display (OSD) languages	DEU, DUT, ENG, ESP, FRE, ITA, RUS
AC input voltage	220-230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	370 W

Weight and Dimensions

Depth	441 mm
Width	435 mm
Height	185 mm
Weight	15300 g