Roland GO:KEYS 5 Reference Manual

70
Editing the system settings
65 65 LOFI CompLOFI Comp
Degrades the sound quality.
L in
L out
R outR in
Compressor Lo-Fi 2-Band EQ
Compressor Lo-Fi 2-Band EQ
MEMO
This eect can be used for both TOTAL FX and MFX. The parameters
than you can set when using the eect with the MFX are limited to
those marked with a (*1).
Parameter Value Explanation
Level
(*1) 0–127 Output Level
Balance
(*1)
D100: 0W–D0:
100W
Volume balance between the direct
sound (D) and the effect sound (W)
Pre Filter Type 1, 2, 3, 4, 5, 6
Selects the type of filter applied to the
sound before it passes through the Lo-Fi
effect.
1: Compressor off
2–6: Compressor on
LoFi Type
1, 2, 3, 4, 5, 6, 7,
8, 9
Degrades the sound quality. The sound
quality grows poorer as this value is
increased.
Post Filter Type OFF, LPF, HPF
Type of filter
OFF: No filter is used
LPF: Cuts the frequency range above the
Cutoff Freq
HPF: Cuts the frequency range below
the Cutoff Freq
Post Filter Cutoff
200, 250, 315, 400,
500, 630, 800,
1000, 1250, 1600,
2000, 2500, 3150,
4000, 5000, 6300,
8000 [Hz]
Basic frequency of the Post Filter
Low Gain -15–+15 [dB]
Amount of boost/cut for the low-
frequency range
High Gain -15–+15 [dB]
Amount of boost/cut for the high-
frequency range
66 66 Bit CrusherBit Crusher
Produces an extreme lo- eect.
L in L out
R outR in
Bit Crusher 2-Band EQ
Bit Crusher 2-Band EQ
MEMO
This eect can be used for both TOTAL FX and MFX. The parameters
than you can set when using the eect with the MFX are limited to
those marked with a (*1).
Parameter Value Explanation
Bit Down
(*1) 0–20 Adjusts the bit depth.
Sample Rate
(*1) 0–127 Adjusts the sample rate.
Filter 0–127 Adjusts the filter depth.
Low Gain -15–+15 [dB]
Amount of boost/cut for the low-
frequency range
High Gain -15–+15 [dB]
Amount of boost/cut for the high-
frequency range
Level 0–127 Output Level
67 67 PhonographPhonograph
Recreates the sound of an analog record being played on a record
player. This lets you simulate the unique noises produced when a
record is played, as well as the variations that occur when the record
spins.
R out
L out
Balance W
Balance W
Balance D
Balance D
L in
R in
Phonograph
Phonograph
MEMO
This eect can be used for both TOTAL FX and MFX. The parameters
than you can set when using the eect with the MFX are limited to
those marked with a (*1).
Parameter Value Explanation
Signal Distortion
(*1)
0–127 Sets the amount of distortion.
Balance
(*1)
D100: 0W
–D0: 100W
Sets the volume balance between the
original sound (D) and the effect sound
(W).
Frequency Range 0–127
Sets the frequency characteristics of the
playback system.
Smaller values create the feeling of an
older system with narrow frequency
bands.
Disc Type LP, EP, SP
Sets the turntable rotation speed.
This has an effect on the scratch noise
cycle.
Scratch Noise 0–127
Sets the volume of noise created by
scratches in the record.
Dust Noise Level 0–127
Sets the volume of noise created by dust
on the record.
Hiss Noise Level 0–127
Sets the volume of continuous hiss
noise.
Total Noise Level 0–127 Sets the volume of noise overall.
Wow 0–127
Sets the amount of variation in record
spin
(long cycle).
Flutter 0–127
Sets the amount of variation in record
spin
(short cycle).
Random 0–127
Sets the amount of non-cyclical
variation in record spin.
Total Wow/Flutter 0–127
Sets the volume of variation in record
spin overall.
Level 0–127 Sets the output volume.

Roland GO:KEYS 5 Specifications

General

Brand	Roland
Model	GO:KEYS 5
Category	Electronic Keyboard
Language	English