Roland GO:KEYS 5 Reference Manual

69
Editing the system settings
61 61 Tape EchoTape Echo
A virtual tape echo that produces a realistic tape delay sound. This
simulates the tape echo section of a Roland RE-201 Space Echo.
R out
L out
Echo Level
Echo Level
Direct Level
Direct Level
L in
R in
Tape Echo
MEMO
This eect can be used for both TOTAL FX and MFX. The parameters
than you can set when using the eect with the MFX are limited to
those marked with a (*1).
Parameter Value Explanation
Repeat Rate
(*1) 0–127
Tape speed
Increasing this value will shorten the
spacing of the delayed sounds.
Intensity
(*1) 0–127 Amount of delay repeats
Mode
S, M, L, S+M, S+L,
M+L, S+M+L
Combination of playback heads to use
Select from three different heads with
different delay times.
S: short
M: middle
L: long
Bass -15–+15 [dB]
Boost/cut for the lower range of the
echo sound
Treble -15–+15 [dB]
Boost/cut for the upper range of the
echo sound
Head S Pan L64–63R
Independent panning for the short,
middle, and long playback heads
Head M Pan L64–63R
Head L Pan L64–63R
Tape Distortion 0–5
Amount of tape-dependent distortion
to be added
This simulates the slight tonal changes
that can be detected by signal-analysis
equipment. Increasing this value will
increase the distortion.
W/F Rate 0–127
Speed of wow/flutter
(complex variation
in pitch caused by tape wear and rotational
irregularity)
W/F Depth 0–127 Depth of wow/flutter
Echo Level 0–127 Volume of the echo sound
Direct Level 0–127 Volume of the original sound
Level 0–127 Output Level
62 62 M/S Delay M/S Delay (Mid-Side Delay)(Mid-Side Delay)
This eect applies dierent amounts of delay to left/right signals of
similar phase and diering phase.
L in L out
R outR in
Side
Mid
LR
MS
MS
LR
Multi-Tap
Delay
Multi-Tap
Delay
Parameter Value Explanation
S Delay Level 0–127
Delay volume of left/right input signals
whose phase is distant
(opposite phase)
M Delay Level 0–127
Delay volume of left/right input signals
whose phase is similar (in phase)
63 63 DJFX LooperDJFX Looper
Loops a short portion of the input sound. You can vary the playback
direction and playback speed of the input sound to add turntable-type
eects.
R out
L out
Loop Sw
L in
R in
Delay
Delay
Delay
Speed
Control
Delay
Speed
Control
Delay
Delay
Parameter Value Explanation
Speed -1.00–+1.00
Specifies the playback direction and
playback speed.
- direction: Reverse playback
+ direction: Normal playback
0: Stop playback
As the value moves away from 0, the
playback speed becomes faster.
Loop Sw OFF, ON
If you turn this on while the sound is
heard, the sound at that point will be
looped. Turn this off to cancel the loop.
* If the effect is recalled with this ON,
this parameter must be turned OFF
and then turned ON again in order to
make the loop operate.
64 64 BPM LooperBPM Looper
Loops a short portion of the input sound. This can automatically turn
the loop on/o in synchronization with the rhythm.
R out
L out
L in
R in
Loop Sw
Control
Loop Sw
Control
Delay
Delay
Delay
Delay
Parameter Value Explanation
Rate
(note)
Note
Ø “Note” (p. 75)
Cycle at which the loop automatically
turns on/off
Length 230–23 Specifies the length of the loop.

Roland GO:KEYS 5 Specifications

General

Brand	Roland
Model	GO:KEYS 5
Category	Electronic Keyboard
Language	English