EasyManuals Logo

Sony XAV-AX150 Service Manual

Sony XAV-AX150
72 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #4 background imageLoading...
Page #4 background image
XAV-AX150
4
Sony CONFIDENTIAL
For Authorized Servicer
SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to ow) than
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
REPLACING THE LITHIUM BATTERY (CR2025) OF THE
REMOTE COMMANDER
When the battery becomes weak, the range of the
remote commander becomes shorter.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type.
Note on the lithium battery
Keep the lithium battery out of the reach of children. Should
the battery be swallowed, immediately consult a doctor.
+ side up
q
Lithium battery (CR2025)
IMPORTANT NOTE FOR REPAIRING
This unit might contain individual personal information that the
customer registered in the replaced old part because it installs the
handsfree function of BLUETOOTH.
Therefore, when repairing, because the data that the customer regis-
tered might disappear, get the approval of the customer beforehand.
If any of the following repair is performed, that data disappears.
Complete DISPLAY board replacing
Factory reset (Initialize)
Note: Be sure to destroy the replaced old DISPLAY board with a hammer
before dispose it.
ABOUT INSTALLATION OF THIS UNIT FOR WORKING
Due to the structure of the unit, you cannot stably place it on at
surfaces.
Stabilize the unit by placing a stand, etc. under it that is suitable for
your work.
stand, etc.
NOTE FOR SECURITY FUNCTION
This unit does not use security function by password lock.
IMPORTANT NOTE FOR REPLACING THE MAIN BOARD
OR IC801 ON THE MAIN BOARD
When the MAIN board or IC801 on the MAIN board is replaced, be
sure to perform the following works.
CHECKING AND SETTING METHOD OF DESTINATION
CODE (Refer to page 5)
FLICKER ADJUSTMENT (Refer to page 28)
TOUCH PANEL ADJUSTMENT (Refer to page 10)
COMMUNICATION CHECK OF Apple CarPlay OR Android
Auto (Refer to page 7)
IMPORTANT NOTE FOR REPLACING THE DISPLAY
BOARD
When the DISPLAY board is replaced, be sure to perform the fol-
lowing works.
FLICKER ADJUSTMENT (Refer to page 28)
COMMUNICATION CHECK OF Apple CarPlay OR Android
Auto (Refer to page 7)
SYSSET
2020/02/0723:51:10(GMT+09:00)

Other manuals for Sony XAV-AX150

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sony XAV-AX150 and is the answer not in the manual?

Sony XAV-AX150 Specifications

General IconGeneral
Display Size6.2 inches
Resolution800 x 480 pixels
BluetoothYes
Apple CarPlayYes
Android AutoYes
TouchscreenYes
Rear View Camera InputYes
Compatible Audio FormatsMP3, WMA, AAC, FLAC
InputsUSB, AUX
OutputsPreamp Outputs
EQ10-band equalizer
USB InputYes
Preamp Outputs3 Pairs (Front, Rear, Sub)
Power Output20W RMS x 4 channels
USB Port1

Related product manuals