Xerox 560 Reference Manual

Designation Function
EI External interrupt group inhibit. The three
interrupt group inhibit bits (CI, II, and EI)
determine whether certain interrupts are al-
lowed to occur. The function of these group
interrupt inhibits are described in "Central-
i zed Interrupt System ", later in th is chapter.
A master mode or master-protected mode pro-
gram can change the group interrupt inhibits
by executing an LPSD, XPSD, PSS, PLS, or
WRITE DIRECT (WD) instruction. These priv-
ileged instructions are described in Chap-
ter 3, "Control Instructions ".
RP Register pointer. This 2-bit field selects one
of the 4 possible blocks of general-purpose
registers as the current register block. A
master or
master-protected mode program can
change the register pointer by executing
LPSD, XPSD, PSS, PLS, or the LOAD REG-
ISTER POINTER (LRP) instruction. LRP is
described in Chapter 3, under "Control
Instructions" •
RA Register altered bit. When a trap occurs,
this bit is set to one when any general reg-
ister or location in memory has been altered
in the execution or partial execution of the
instruction that caused the trap.
MA Mode altered. This bit is used to invoke both
the master-protected mode of operation and
the real-extended addressing mode). Table 1
detai Is the function of the setting of this bit
in conjunction with the setting of the MS
(bit 8)and MM (bit 9) fields. The bits are set
by an LPSD, XPSD, PSS, or PLS instruction.
MP
Memory protection violation address. If the
X PSD instruction is being executed in a trap
routine as a result of a memory protection
violation and the SP bit in the XPSD is a one,
the effective virtual address causing the
violation is stored in the fourth word. This
storage may be invoked so that memory pro-
tection violations can be recorded.
CENTRALIZED INTERRUPTS
The system includes a single, centralized interrupt feature.
A II int.orrllntc; nr"" t""rrninnt.orl in thQ ,,,darn r .... ntrnl Pr .... _
........ _ .. _ .... __ ._ ._ ....... _. __ ...... __ ,_._00. __ .... _ ... _
cessor. The System Control Processor is described earl ier
and also in Chapters 5 and 6.
When a condition that wil I result in an interrupt is sensed,
a signal
is sent to the corresponding interrupt level. If
that level is "armed", it advances to the waiting state.
30 Centralized Interrupts
When
all the conditions for acknowledging the interrupt
have been achieved, the basic processor stops executing
the current program and executes the instruction in the cor-
responding interrupt location. After the basic processor has
successfully accessed the interrupt instruction, it advances
the interrupt level to the active state. The basic processor
may
actually execute many program instructions between
the time that the interrupt-requesting condition is sensed
and the time that the actual interrupt acknowledgment oc-
curs. After the interrupt is completely processed, the basic
processor returns to the interrupted program and resumes its
execution.
STATES OF AN INTERRUPT LEVEL
An interrupt level is mechanized by means of three flip-
flops. Two flip-flops are used to define four mutually ex-
clusive states; disarmed, armed, waiting, and active. The
third
flip-flop provides the disabled/enabled function and
is independent of the defined state. The various states and
the conditions of interrupt levels are described in the fol-
lowing paragraphs. Figure 10 conceptually illustrates the
operational state changes of a typica I interrupt level.
DISARMED
When an interrupt level is in the disarmed state, no signal
is admitted to that interrupt level; that is, the level neither
accepts nor remembers an interrupt event, nor is any pro-
gram interrupt caused by it at any time.
Although an interrupt level can change from any state to
the disarmed state, only a special form of the WRITE DIRECT
instruction (WD) can cause a disarmed level to change to
another state. The WD instruction is described in Chap-
ter 3, "Control Instructions ".
ARMED
When an interrupt level is in the armed state, it can accept
and remember an interrupt signal. The receipt of such a sig-
nal advances the interrupt level to the waiting state where
it remains until
it is allowed to advance to the active state.
A special form of the WD instruction can cause an armed
level
to be advanced directly to the active state.
A level can change from any state to the armed state.
WAITING
For
an interrupt level to be in the waiting state, that level
must
have been previously armed and received an interrupt
signal. The signal may have been generated externally,
internally, or have resulted from a WD operation. Any
signals received by an interrupt level already in the waiting
state are ignored.

Xerox 560 Specifications

General

Brand	Xerox
Model	560
Category	Printer
Language	English