• This product is not suitable for children except under the direct supervision of
an adult.
• Carefully read all manufacturers warnings and cautions for any parts used
in the construction and use of your model.
• Assemble this kit only in places away from the reach of very small children.
• First-time builders should seek advice from people who have building
experience in order to assemble the model correctly and to allow the model
to reach its performance potential.
• Exercise care when using tools and sharp instruments.
• Take care when building, as some parts may have sharp edges.
• Keep small parts out of reach of small children.
• Immediately after using your model, do NOT touch equipment on the model
such as the engine and muffler, because they generate high temperatures.
You may burn yourself seriously touching them.
• Follow the operating instructions for the radio equipment at all times.
• Do not put fingers or any objects inside rotating and moving parts, as this
may cause damage or serious injury.
• Be sure that your operating frequency is clear before turning on or running
your model, and never share the same frequency with somebody else at the
same time. Ensure that others are aware of the operating frequency you are
using and when you are using it.
• Always turn on your transmitter before you turn on the receiver in the car.
Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of
the radio equipment.
• Disconnect the battery pack before storing your model.
• When learning to operate your model, go to an area that has no obstacles
that can damage your model if your model suffers a collision.
• Remove any sand, mud, dirt, grass or water before putting your model away.
• If the model behaves strangely, immediately stop the model, check and clear
the problem.
• To prevent any serious personal injury and/or damage to property, please
be responsible when operating all remote controlled models.
• Do not use your model:
- Near real cars, animals, or people that are unaware that an R/C car is
being driven.
- In places where children and people gather
- In residential districts and parks
- In limited indoor spaces
- In wet conditions
- In the street
- In areas where where loud noises can disturb others, such as hospitals and
residential areas.
22
FRONT MULTI-DIFF
™
SETTINGS
STANDARD ONE-WAY SOLID ONE-WAY FULL-TIME SOLID AXLE
Outdrive shafts (left and right) are not connected to each
other, nor to front main axle.
Off-power:
Outdrive shafts rotate forward independently of each other
and front main axle.
On-power:
Both outdrive shafts rotate with front main axle (locked in
one-way bearings)
Best used when...
traction is high, the car leans towards off-power understeer
and the track does not require braking for the corners. Will
give maximum off-power steering and increase efficiency
(more runtime). Best suited to a smooth driving style.
Both outdrive shafts (left and right) are connected
together by internal locking axle, but are not
connected to front main axle.
Off-power:
Both connected outdrive shafts rotate forward
together (but independent of front main axle).
On-power:
Both outdrive shafts rotate with front main axle
(locked in one-way bearings).
Best used when...
traction is medium to high and the track does not
require braking for the corners. Will give good off-
power steering and efficiency.
Both outdrive shafts (left and right) are connected
to front main axle by internal locking axle and
locking pin.
Off-power and on-power:
Both outdrive shafts rotate with front main axle.
Best used when...
traction is low to medium, the car leans towards
off-power oversteer and/or the track requires
braking for the corners. Will give less off-power
steering and efficiency (less runtime). Best suited to
an aggressive driving style.
Cutaway view Cutaway view Cutaway view
Front main axle
Outdrive shaft
(Left)
Outdrive shaft
(Right)
Front main axle
Outdrive shaft
(Left)
Outdrive shaft
(Right)
Locking axle
Front main axle
Outdrive shaft
(Left)
Outdrive shaft
(Right)
Locking
axle
Locking
pin
O-ring
Spacer
Spacer
Spacer
Spacer
Spacer
Spacer
SAFETY PRECAUTIONS
Take enough safety precautions prior to operating this model. You are responsible
for this model‘s assembly and safe operation! Please read the instruction manual
before building and operating this model and follow all safety precautions. This
product contains a chemical known to the State of California to cause cancer and
birth defects or other reproductive harm. Always keep the instruction manual at
hand for quick reference, even after completing the assembly. Use only genuine
and original authentic Xray parts for maximum performance.
Improper operations may cause personal and/or property damage. XRAY and
its distributors have no control over damage resulting from shipping, improper
construction, or improper usage. XRAY assumes and accepts no responsibility for
personal and/or property damages resulting from the use of improper building
materials, equipment and operations. By the act of assembling or operating this
product, the user accepts all resulting liability. If the buyer is not prepared to
accept this liability, then he/she should return this kit in new, unassembled, and
unused condition to the place of purchase.The T1FK‘05 is a high competition,
high quality, 1/10-scale electric touring car for persons age 14 and older. This is
not a toy, it is a precision racing model.
XRAY guarantees this model kit to be free from defects in both material and
workmanship. The total monetary value under warranty will in no case exceed the
cost of the original kit purchased. This warranty does not cover any components
damaged by use or modification or as a result of wear. Part or parts missing from
this kit must be reported within 60 days of purchase. No part or parts will be sent
under warranty without proof of purchase. Should you find a defective or missing
part, contact the local distributor. Service and customer support will be provided
through local hobby store where you have purchased the kit, therefore make sure
to purchase any XRAY products at your local hobby store.
• Insulate any exposed electrical wiring (using heat shrink tubing or electrical tape)
to prevent dangerous short circuits.
• Use a recommended charger for the receiver and transmitter batteries and
follow the instructions correctly. Over-charging, incorrect charging, or using
inferior chargers can cause the batteries to become dangerously hot.
• Regularly check the charger for potential hazards such as damage to the cable,
plug, casing or other defects. Ensure that any damage is rectified before using
the charger again.
• Do not allow the transmitter batteries to become low on charge, otherwise you
risk losing control of the model.
• Do not allow any metal part to short circuit the receiver batteries or other
electrical/electronic device on the model.
IMPORTANT NOTES – GENERAL
IMPORTANT NOTES – ELECTRICAL
To Next Page
Loading...
Need help?
General
