3 Utility Function Mode
3.2.12 Gain Adjustment of Analog Monitor Output (Fn00D)
3-30
3.2.12 Gain Adjustment of Analog Monitor Output (Fn00D)
This function is used to manually adjust the gains for the analog monitor outputs
(torque reference monitor output and motor speed monitor output). The gain values
are factory-set before shipping. Therefore, the user need not usually use this function.
The setting range of the gain adjustment width for analog monitor output is
-128 to +127 (× 0.4%).
The setting of gain adjustment width is made on the base of 100%. For example, the
setting “-125” makes 100% - (125 × 0.4%) = 50%, which means that the monitor
output voltage is 1/2. The setting “125” makes 100% + (125 × 0.4%) = 150%, which
means that the monitor output voltage is 1.5 times.
Note: The adjustment value will not be initialized when parameter settings are initialized using
Fn005.
(1) Preparation
The following condition must be met to adjust the gain of the analog monitor output.
• The write prohibited setting (Fn010) must not be set to write-protect parameters.
(2) Operating Procedure
Use the following procedure.
Step Display after Operation Keys Operation
1
Press the Key to view the main
menu for the utility function mode.
Use the
or Key to move
through the list and select Fn00D.
2
Press the
Key. The display
changes to the Fn00D execution dis-
play.
3
Press the
or Key to
adjust the gain adjustment width of
CH1 (torque reference monitor).
4
After the gain adjustment of CH1 has
completed, adjust the gain adjustment
width of CH2 (motor speed monitor).
Press the
Key. The cursor
moves to CH2 side.
㧮㧮ޓޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧜㧜㧲㧦㧯㨡㨞㧹㨍㨚㨡㧭㨐㨖
㧲㨚㧜㧜㧱㧦㧯㨡㨞㧭㨡㨠㨛㧭㨐㨖
㧲㨚㧜㧜㧰㧦㧹㨛㨚㧳㨍㨕㨚ޓ㧭㨐㨖
㧲㨚㧜㧜㧯㧦㧹㨛㨚㨆㨑㨞㨛ޓ㧭㨐㨖
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩ޓ㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
㧮㧮ޓޓޓޓޓ㧙㧳㨍㨕㨚ޓ㧭㧰㧶㧙
㧯㧴㧝㧩ޓ㧜㧜㧝㧞㧡
㨁㨚㧜㧜㧞㧩ޓ㧜㧜㧜㧜㧜
㧯㧴㧞㧩㧙㧜㧜㧜㧜㧝
㨁㨚㧜㧜㧜㧩ޓ㧜㧜㧜㧜㧜
To Next Page
Loading...
Need help?
General
