AMX DGX800-ENC User Manual

Appendix C – DGX_SHELL Commands
251
Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers
reboot This command can be used to reboot individual components or the system as a whole.
NOTE: DXLink Twisted Pair I/O Boards only - The reboot command can be used to reboot a specific
endpoint connected to the board. Use the y variable to specify the connector attached to the endpoint (the
DXLink Twisted Pair Module or Wallplate) you want to reboot.
Usage: reboot {abdf:iprsu}{MCPU}{BCPU|BCPUx|BCPUx:y|BCPUx:y:z}{CENTER|CENTERx}{PPIC}
{EXPIN|EXPINx}{EXPOUT|EXPOUTx}
NOTE: EXPIN refers to an expansion board on the input side of the enclosure; EXPOUT refers to an
expansion board on the output side.
Options:
-a ac power cycle
-b backplane reset line
-d delay <seconds>
-f force (suppress prompting)
-i immediate
-p ppic reset line; hardware reboot of the PowerPic - toggle its MCLR (Hardware Master Clear) pin
-r redundant reset (backplane reset line) hardware reboot of all boards except the CPU board - toggles their
MCLR (Hardware Master Clear) pins
-s staged reset
-u subsystem <default=0 remote_power=1 local_transport=2 endpoint_transport=3 ethernet_phy=4
ethernet_switch=5 av_path=6>
Target:
MCPU
BCPU
BCPUx x = 1-4 (DGX800), 1-8 (DGX1600), 1-16 (DGX3200), 1-32 (DGX6400)
BCPUx:y y = 0-3 (channel-hardware order, variable only applies to DXLink Twisted Pair I/O Boards)
BCPUx:y:z z = 0-7 (port)
CENTER use for an Enova DGX 800/1600 or to target all centers in an Enova DGX 3200/6400
CENTERx where x = 1-4 for an Enova DGX 3200/6400
PPIC
EXPIN (expansion board in the input section of the enclosure)
EXPINx where x = 1-4 for an Enova DGX 6400 (expansion board in input section of enclosure)
EXPOUT (expansion board in the output section of the enclosure)
EXPOUTx where x = 1-4 for an Enova DGX 6400 (expansion board in output section of enclosure)
• If no specific targets are chosen, the command will apply to all possible targets.
• If -r is selected, a hardware line to all I/O boards is forced low then released, causing the boards to
experience a hard MCLR (Hardware Master Clear).
• If -s is selected, in addition to having the main power supplies turned off, a hardware connection to the
PowerPIC is forced low then released, causing the PowerPIC to experience a hard MCLR.
reset This command resets settings and other system data to their default values.
Usage: reset [options] <action>
Actions:
factory (apply system default settings to MCPU and BCPUs)
Options:
--help, -h (displays command usage information. NOTE: In elevated shell user levels, run reset -h to
display information on additional options.)
Example:
reset factory Apply defaults to MCPU and BCPUs
sc This command sends an ICSP Send Command to a Port of the 5002 device.
Usage: sc
Actions:
<port> <command> Destination Device Port and Command
Example:
sc 1 AUDOUT_MUTE-ENABLE
Basic DGX_SHELL Commands
reset command

AMX DGX800-ENC Specifications

General

Brand	AMX
Model	DGX800-ENC
Category	Switch
Language	English