AMX DGX800-ENC User Manual

Enova DGX DXLink™ Twisted Pair 4K Boards
97
Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers
HDCP Compliance
If a connected downstream sink is not HDCP compliant, then the Output Board will not send the signal to it. This does not affect
other outputs the source may be routed to. This allows compliant displays to show content from source devices even if the source
devices are switched to non-compliant displays. Non-compliant displays can easily be identified because they display a dark red
image (via an HDMI/DVI Output) or an orange image (via a DXLink RX) to indicate that the authentication process failed.
InstaGate Pro
®
Technology
DXLink Twisted Pair 4K Boards meet HDCP standards and support InstaGate Pro Technology. For information on HDCP
functionality for DXLink boards, see “HDCP Support on Enova DGX Switchers” on page 70.
DXLink Twisted Pair 4K Boards provide EDID emulation support with plug-and-play information provided by the Enova DGX
Switcher.
DXLink Twisted Pair 4K input and output connectors incorporate HDMI Technology, are HDCP 1.4 compatible, and feature
InstaGate Pro Technology* for low-latency switching of HDCP protected content. The DXLink Twisted Pair 4K connectors
also support embedded audio, both linear PCM (stereo audio) and non-linear PCM (Dolby Digital, Dolby TrueHD, DTS, etc.).
* InstaGate Pro Technology eliminates HDCP latency and interruptions on all displays in a system. (These conditions are typically
experienced when HDCP authenticates HDMI source and destination devices.) Key limitations on source devices are also eliminated
by allowing them to see only a single sink key from the DXLink Twisted Pair 4K Input Board’s input connection. With InstaGate Pro
Technology, when a source requires HDCP encrypted content, the inputs and compliant downstream devices are automatically
authenticated.
Enova DGX DXLink™ Twisted Pair 4K Boards – Specifications
Applies to input board FG1061-570 (DGX-I-DXL-4K) and output board FG1061-580 (DGX-O-DXL-4K). This section applies to
products with full compatibility (including a complete 4K signal path). For compatibility between DXLink Twisted Pair 4K products
and DXLink Twisted Pair products, see the DXLink Twisted Pair 4K Transmitters and Receivers Hardware Reference Manual.
Compatible AMX DXLink™ Twisted Pair 4K Transmitters and Receivers:
DXLink 4K HDMI Decor Style Wallplate TX: FG1010-330-BL and FG1010-330-WH (DX-TX-DWP-4K)
DXLink 4K HDMI RX: FG1010-510 (DX-RX-4K)
Compatible AMX Solecis 4K Digital Switchers (1 Output per Switcher):
Solecis 4x1 4K HDMI Digital Switcher with DXLink Output: FG1010-314 (SDX-414-DX)
Solecis 5x1 4K Multi-Format Digital Switcher with DXLink Output: FG1010-355 (SDX-514M-DX)
IMPORTANT: DXLink twisted pair cable runs for DXLink equipment shall only be run within a common building. “Common building” is
defined as: Where the walls of the structure(s) are physically connected and the structure(s) share a single ground reference.
Enova DGX DXLink Twisted Pair Board Specifications
Parameter Value
Compatible AMX DXLink™
Twisted Pair 4K Products
4K HDMI Decor Style Wallplate TX, 4K HDMI RX, other AMX DXLink signal management products
NOTE: For additional compatibility with DXLink Twisted Pair products, see the “DXLink Twisted
Pair 4K Transmitters and Receivers Hardware Reference Manual” at www.amx.com.
Compatible Formats HDMI Video, Audio, Ethernet, USB (HID), Power, and Control
Signal Type Support DXLink Twisted Pair
Transport Layer Throughput (max.) 10.2 Gbps
Video Data Rate (max.) 8.91 Gbps (max)
Video Pixel Clock (max.) 297 MHz
Progressive Resolution Support 480p up to 4096x2160p,60 Hz*
* Y/Cb/Cr 4:2:0 and 4K RX Scaler in Bypass
NOTE: See full list of supported formats on page 99.
Interlaced Resolution Support 480i, 576i, 1080i
If input is interlaced, all scaled outputs will deinterlace video to a progressive resolution format. If
in scaler Bypass mode, interlaced input will pass through unaltered.
Deep Color Support Up to 1080p: 24-bit, 30-bit, 36-bit
30-bit, 36-bit only supported when the HDMI Output Board Scaler or DXLink RX Scaler is in Bypass
mode and format is 1080p60 or less.
Color Space Support • RGB 4:4:4
• YCbCr 4:4:4, 4:2:2, and 4:2:0
Input signal for YCbCr 4:4:4 and 4:2:2, output color-space is converted to RGB 4:4:4.
4:2:0 only supported at 2160p 50/60Hz with 4K RX Scaler in Bypass.

AMX DGX800-ENC Specifications

General

Brand	AMX
Model	DGX800-ENC
Category	Switch
Language	English