Installation and Setup
40
Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers
Options for System Setup with DXLink Twisted Pair 4K
The following table contains the options in an Enova DGX Switcher for using DXLink Twisted Pair 4K Input and Output Boards in
conjunction with DXLink Twisted Pair 4K Transmitters and Receivers.
A typical system setup for a source and destination is illustrated on page 88 and shows an Enova DGX 1600 with DXLink Twisted
Pair Boards used in conjunction with DXLink Twisted Pair Transmitters and Receivers.
NOTE: Solecis Digital Switchers have a DXLink Twisted Pair output port that optionally provides source point switching and distance
transmission to an Enova DGX DXLink Twisted Pair Input Board for hub-style or campus-wide distribution.
NOTE: Additional compatibility is available between DXLink Twisted Pair 4K and DXLink Twisted Pair equipment (see the “DXLink
Twisted Pair 4K Transmitters & Receivers Hardware Reference Manual”).
Options for System Setup with DXLink Fiber
The following table contains the options for using DXLink Fiber Input and Output Boards in conjunction with DXLink Fiber TXs and
RXs in an Enova DGX Digital Media Switcher. The input/output boards and TX/RX units can be either Duplex or Simplex, as long as
the model types match (multimode to multimode and single mode to single mode).
IMPORTANT: Compatibility between hardware requires matching model types: multimode to multimode and single mode to single
mode.
A typical system setup for a source and destination is illustrated on page 116 and shows an Enova DGX 1600 with DXLink Fiber
Boards used in conjunction with DXLink Fiber Transmitters and Receivers.
Rack Installation and System Setup
Enova DGX 100 Series Switchers can be mounted in a standard EIA 19 in. (48.26 cm) rack.
Required Items for Rack Installation:
□ Enclosure
□ Enova DGX 6400 only – two rack mounting handles (provided)
□ Standard EIA 19 in. (48.26 cm) rack
□ Screwdriver
□ Screws that fit your rack for mounting the enclosure
□ Power cords (provided, if shipped within the US)
□ Surge-protector – highly recommended
Optional Items for Rack Installation:
□ A PC or laptop computer with a null modem cable for communication with the enclosure via the RS-232 serial (Control) port
Installation Recommendations:
Write the serial numbers (normally located on rear of enclosure) in an easily accessible location before installing the
enclosure in a rack.
Use earth-grounded power cords and equipment with an Enova DGX Switcher.
Attach all power cords to a single surge protector and/or an AC line conditioner.
Apply power to the Enova DGX Switcher before applying power to its source and destination devices.
System Setup Options – Enova DGX Boards with DXLink Modules/Wallplates
DXLink Wallplate Enova DGX Input Board Enova DGX Output Board DXLink Module
HDMI 4K Decor Wallplate TX DXLink Twisted Pair DXLink Twisted Pair HDMI 4K RX Module
HDMI 4K Decor Wallplate TX DXLink Twisted Pair Any output board Not applicable
Not Applicable Any input board DXLink Twisted Pair HDMI 4K RX Module
System Setup Options – Enova DGX Boards with DXLink Fiber
DXLink Fiber TX DXLink Fiber Input Board DXLink Fiber Output Board DXLink Fiber RX
Multi-Format MM Fiber TX Multimode Fiber Multimode Fiber HDMI MM Fiber RX
Multi-Format MM Fiber TX Multimode Fiber Single Mode Fiber HDMI SM Fiber RX
Multi-Format MM Fiber TX Multimode Fiber Any output board Not applicable
Multi-Format SM Fiber TX Single Mode Fiber Single Mode Fiber HDMI SM Fiber RX
Multi-Format SM Fiber TX Single Mode Fiber Multimode Fiber HDMI MM Fiber RX
Multi-Format SM Fiber TX Single Mode Fiber Any output board Not applicable
Not Applicable Any input board Multimode Fiber HDMI MM Fiber RX
Not Applicable Any input board Single Mode Fiber HDMI SM Fiber RX
To Next Page
Loading...
Need help?
General
