EasyManuals Logo

Canon LV 7365 User Manual

Canon LV 7365
83 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #70 background imageLoading...
Page #70 background image
6
7. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
WARNING Indicator
LAMP Indicator
Indicator Messages
POWER Indicator
MENU
BACK
KEYSTONE
WARNING
P
O
W
E
R
AUTO PC
INPUT
VOL
-
VOL
+
LAMP



Indicator Condition Projector Condition Note
Off
The main power is off
Blinking light Green 0.5 sec On,
0.5 sec Off
The projector is getting ready
to turn on.
Wait for a moment.
2.5 sec On,
0.5 sec Off
Off Timer is enabled.
Orange 0.5 sec On,
0.5 sec Off
T h e p r o j e c t o r i s c o o l i n g
down.
Wait for a moment.
Steady light Green The projector is turned on.
Orange The projector is in Standby.
Indicator Condition Projector Condition Note
Off Normal
Blinking light Red 1 c y c l e (0 . 5 s e c
On, 2.5 sec Off)
L amp cov er err or or la mp
housing error
Replace the lamp cover or lamp housing correctly.
(
page 60)
2 c yc l e (0 . 5 s e c
On, 0.5 sec Off)
Temperature error The projector is overheated. Move the projector to a
cooler location.
4 c yc l e (0 . 5 s e c
On, 0.5 sec Off)
Fan error Fans will not work correctly.
6 c yc l e (0 . 5 s e c
On, 0.5 sec Off)
Lamp error Lamp fails to light. Wait a full minute and then turn on
again.
Green Re-firing the lamp (The pro-
jector is cooling down.)
The projector is re-firing.
Wait for a moment.
Steady light Orange Key lock is on. You have pressed cabinet button when Key lock is on.
(
page 50)
Indicator Condition Projector Condition Note
Off Normal
Blinking light Red Lamp has reached its end of life. Lamp
replacement message will be displayed.
Replace the lamp.
Steady light Red Lamp has been used beyond its limit.
The projector will not turn on until the
lamp is replaced.
Replace the lamp.
Green Lamp mode is set to Quiet mode.
If a temperature error occurs
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the
WARNING indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
- Unplug the power cord after the cooling fans stop.
- Move the projector to a cooler location if the room where you are presenting is particularly too warm.
- Clean the ventilation holes if they are clogged with dust.
- Wait about 60 minutes until the inside of the projector becomes cool enough.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Canon LV 7365 and is the answer not in the manual?

Canon LV 7365 Specifications

General IconGeneral
Vertical scan range50 - 120 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Contrast ratio (typical)500:1
Screen size compatibility300 \
Projector native resolutionXGA (1024x768)
FocusManual
Digital zoom4 x
Focal length range17.7 - 28.3 mm
Aspect ratio4:3
Dimensions (WxDxH)310 x 265 x 109 mm
Power requirements100V - 240V AC, 50/60Hz
Lamp typeNSH
Lamp power210 W
Light source typeLamp
Dot clock scanning frequency108 MHz
RMS rated power5 W
Headphone outputs1
Power consumption (standby)9 W
Power consumption (typical)295 W
Weight and Dimensions IconWeight and Dimensions
Weight3300 g

Related product manuals