Canon VB-M40 User Manual

5-28
Certificates
1 [Create Self-Signed Certificate]
After entering each of the following settings, click
[Exec] to create a self-signed certificate. Follow the
instructions in the message and reboot. The certificate
created will take effect after rebooting.
Note
Creating a certificate takes time, so it is recommended that you
stop video transmission and upload processes.
2 [Certificate Status]
If no certificate is installed, [Not Installed] will appear. If
a certificate is installed, [Installed] will appear.
3 [Country (C)]
Enter the country code.
4 [State/Province (ST)], [Locality (L)], [Organization (O)],
[Organizational Unit (OU)], [Common Name (CN)]
Enter state/province name, locality, organization name,
organizational unit and common name in ASCII
characters (spaces or printable characters). Enter a
FQDN format host name, etc. to set the common name
(required).
5 [Validity Period Start Date], [Validity Period End Date]
Set the validity period of the certificate to be created in
the range of 2001/01/01 to 2031/12/31 (required when
creating a self-signed certificate).
Certificate Management
1 [Generate Certificate Signing Request]
Click [Exec] to create server private key and a self-
certification authority private key to generate a
certificate signing request. Once processed, the
certificate signing request will appear in a separate
window.
Note
Generating a certificate signing request takes time, so it is
recommended that you stop video transmission and upload
processes.
2 [Display Certificate Signing Request Details]
Click [Exec] to view the details of the certificate signing
request.
3 [Install Server Certificate]
Perform this operation to install a server certificate.
Click [Browse] to select the certificate file for
installation, then click [Exec]. The certificate installed
will take effect after rebooting.
4 [Install Intermediate CA Certificate]
Perform this operation to install an intermediate CA
certificate. Select the certificate file to be installed
using the [Browse] button and click [Exec]. The
installed certificate will take effect after rebooting.
5 [Delete Certificate]
Click [Exec] to delete the certificate. However, if SSL
communications are enabled, the certificate cannot be
deleted. Set [SSL Communications] to [Disable] before
deleting a certificate. The deletion will take effect after
rebooting.
6 [Display Server Certificate Details]
Click [Exec] to view the details of the certificate.
[SSL/TLS] Setting HTTP Communication Encryption
The following can be set here.
• Certificates
Create an SSL/TLS certificate.
• Certificate Management
Manage the SSL/TLS certificate.
• Encrypted Communications
Set the encypted communication.
Important
With regard to security, it is recommended that you use a self-
signed certificate where complete security does not need to be
ensured through operation tests, etc. For system operation,
acquire and install a certificate issued by a CA.

Canon VB-M40 Specifications

General

Total megapixels	1.3 MP
Maximum resolution	1280 x 960 pixels
Supported video modes	-
Video formats supported	H.264
Supported graphics resolutions	160 x 120, 320 x 240, 1280 x 960, 640 x 480 (VGA)
Pan range	-170 - 170 °
White balance	Auto, Manual
Tilt angle range	-90 - 10 °
Minimum illumination	0.01 lx
Sensor type	CMOS
Optical sensor size	1/3 \
Digital zoom	4 x
Optical zoom	20 x
Focal length range	4.7 - 94 mm
Built-in HDD	No
Card reader integrated	Yes
Compatible memory cards	SD, SDHC
Form factor	Covert
Product color	Black
Type	IP security camera
Placement supported	Indoor
Connectivity technology	Wired
Interface	RJ-45
Headphone outputs	1
Cabling technology	10/100Base-T(X)
AC input voltage	100-240 V
Power source type	PoE
AC input frequency	50 Hz
Storage temperature (T-T)	5 - 85 °C
Operating temperature (T-T)	-10 - 50 °C

Weight and Dimensions

Width	132 mm
Height	155 mm
Weight	1150 g