Epson EH-TW6000 User Manual

Troubleshooting
68
Indicators Status Remedy
(red)
Lamp Error
Lamp Failure
There is a problem with the lamp, or it failed to turn on.
•
Disconnect the power cable, and then check if the lamp is
cracked.
s p.81
If it is not cracked, reinstall the lamp and turn on the power.
If reinstalling the lamp does not fix the problem, or if the lamp is
cracked, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest Epson repair center.
s Epson Projector Contact List
•
If the air filter is clogged, clean it. s p.77
•
When using at an altitude of 1500 m or more, set High Altitude
Mode to On.
s Extended - Operation - High Altitude
Mode p.63
(red)
High Temp Error
(Overheating)
The internal temperature is too high.
•
The lamp turns off automatically and projection stops. Wait for
about five minutes. When the fan has stopped, disconnect the
power cable.
•
If the projector is installed next to a wall, make sure there is at
least 20 cm between the wall and the projector's exhaust vent.
•
If the air filter is clogged, clean it. s p.77
•
If turning the power back on does not clear the problem, stop
using the projector and remove the power plug from the elec-
trical outlet. Contact your local dealer or the nearest Epson repair
center.
s Epson Projector Contact List
Indicator status during normal operation
: Lit : Flashing : Off
Indicators Status Remedy
(blue)
Standby condition
When you press the button on the remote control, or the
button on the control panel, projection starts after a short
wait.
(blue)
Warm-up in progress
Warm-up time is about 30 seconds.
The power-off operation is disabled while the projector is warm-
ing-up.
(blue)
Cool-down in pro-
gress
All operations are disabled while the projector is cooling-down.
The projector enters standby condition when cool-down is com-
plete. If for any reason the power cable is disconnected during
cool-down, wait until the lamp has cooled down sufficiently
(about 10 minutes), reconnect the power cable, and then press
the
button on the remote control, or the button on the
control panel.

Epson EH-TW6000 Specifications

General

Matrix size	0.61 \
Projection distance	2.95 - 4.8 m
Projection technology	LCD
Contrast ratio (typical)	-
Screen size compatibility	- \
Projector native resolution	1080p (1920x1080)
Keystone correction, horizontal	± 30 °
Aspect ratio	16:9
RS-232 ports	1
Connectivity technology	Wired
Focal length range	18.2 - 29.2 mm
Aperture range (F-F)	1.51 - 1.99
Lamp type	UHE
Lamp power	230 W
Light source type	Lamp
Service life of light source	5000 h
DVI port	No
AC (power) in	Yes
USB connector type	USB Type-A
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
S-Video inputs quantity	0
Supported video modes	1080p
Supported graphics resolutions	1920 x 1080 (HD 1080)
RMS rated power	20 W
Product color	Black
Market positioning	Home cinema
Power source	AC
AC input voltage	100 - 240 V
Voltage tolerance	10 %
AC input frequency	50 - 60 Hz
Power consumption (standby)	- W
Power consumption (typical)	274 W
Noise level	- dB
Noise level (economic mode)	24 dB

Weight and Dimensions

Weight	6000 g