Epson EH-TW9100W User Manual

Troubleshooting
80
Indicators Status Remedy
(red)
Lamp Error
Lamp Failure
There is a problem with the lamp, or it failed to turn on.
•
Disconnect the power cable, and then check if the lamp is
cracked.
s p.94
If it is not cracked, reinstall the lamp and turn on the power.
If reinstalling the lamp does not fix the problem, or if the lamp is
cracked, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest Epson repair center.
s Epson Projector Contact List
•
If the air filter is clogged, clean it. s p.90
•
When using at an altitude of 1500 m or more, set High Altitude
Mode to On.
s Extended - Operation - High Altitude
Mode p.75
(red)
High Temp Error
(Overheating)
The internal temperature is too high.
•
The lamp turns off automatically and projection stops. Wait for
about five minutes. When the fan has stopped, disconnect the
power cable.
•
If the projector is installed next to a wall, make sure there is at
least 20 cm between the wall and the projector's exhaust vent.
•
If the air filter is clogged, clean it. s p.90
•
If turning the power back on does not clear the problem, stop
using the projector and remove the power plug from the elec-
trical outlet. Contact your local dealer or the nearest Epson repair
center.
s Epson Projector Contact List
Indicator status during normal operation
: Lit : Flashing : Off
Indicators Status Remedy
(blue)
Standby condition
When you press the button on the remote control, or the
button on the control panel, projection starts after a short
wait.
(blue)
Warm-up in progress
Warm-up time is about 30 seconds.
The power-off operation is disabled while the projector is warm-
ing-up.
(blue)
Cool-down in pro-
gress
All operations are disabled while the projector is cooling-down.
The projector enters standby condition when cool-down is com-
plete. If for any reason the power cable is disconnected during
cool-down, wait until the lamp has cooled down sufficiently
(about 10 minutes), reconnect the power cable, and then press
the
button on the remote control, or the button on the
control panel.

Epson EH-TW9100W Specifications

General

RS-232 ports	1
Matrix size	0.74 \
White light output	2400 ANSI lumens
Projection distance	- m
Projection technology	3LCD
Screen size compatibility	30 - 300 \
Projection distance (tele)	1.9 - 19.2 m
Projection distance (wide)	0.9 - 9 m
Projector native resolution	1080p (1920x1080)
Keystone correction, vertical	-30 - 30 °
Full HD	Yes
Color modes (2D)	Dynamic, Cinema
Supported 3D formats	Side by side, Top and bottom, Frame packing
Analog signal format system	-
Focus	Manual
Focal length range	23 - 47 mm
Aperture range (F-F)	2 - 3.17
Vertical lens shift range	-96.3 - 96.3 %
Horizontal lens shift range	-47.1 - 47.1 %
Lamp type	E-TORL
Lamp power	230 W
Light source type	Lamp
Service life of light source	4000 h
Service life of light source (economic mode)	5000 h
DVI port	No
Serial interface type	RS-232
USB 2.0 ports quantity	0
Noise level	- dB
Country of origin	China
2D/3D frequency image	240/480 Hz
Noise level (economic mode)	22 dB
Placement	Desktop
Product type	Standard throw projector
Product color	White
Market positioning	Home cinema
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.39 W
Power consumption (typical)	340 W
Power consumption (economy mode)	287 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	5 - 35 °C
Pallet width	800 mm
Pallet height	2244 mm
Pallet length	1200 mm
Pallet width (UK)	1000 mm
Quantity per pack	1 pc(s)
Quantity per pallet	12 pc(s)
Quantity per pallet layer	2 pc(s)

Weight and Dimensions

Depth	395 mm
Width	466 mm
Height	140 mm
Weight	8400 g
Package depth	573 mm
Package width	531 mm
Package height	350 mm
Package weight	13050 g