Fujitsu fi-6110 User Manual

Chapter 4 How to Use the Operator Panel
Appendix
Glossary
Introduction
Index
Contents
TOP
50
How to Load
Documents
How to Use the
Operator Panel
Various Ways to
Scan
Daily Care
Troubleshooting
Operational
Settings
Replacing the
Consumables
Scanner
Overview
Configuring the
Scan Settings
Indications on Function Number Display
Display Description
8 Displayed when the scanner has just been powered on.
P Processing initialization.
0 Initialization is almost complete.
1 Ready to start scanning.
Indicates that the initialization was successfully completed.
This state is referred to as "ready".
Function
number
(flash)
A function number will flash after detecting a multifeed. This
indication prompts whether or not to memorize the overlap
pattern.
For details, refer to "Ignoring Multifeed for a Set Pattern"
(page 82).
c
(flash)
Indicates that the ADF was opened when the status was
ready ("1"). Note that the Check LED will also flash.
To return to ready (”1”) status, close the ADF by referring to
" How to Close the ADF" (page 19).
If the display does not return to ready (“1”) after closing the
ADF, turn the power off then back on.
If the problem still persists, contact your FUJITSU scanner
dealer or an authorized FUJITSU scanner service provider.
h
Indicates that the scanner is operating in protection mode.
The scanner may enter this protection mode if it is used for
many hours continuously under high room temperature.
Note that the interval to feed the documents becomes longer
in this mode, but it is not a malfunction. (The recommended
operating environment is 35°C (95°F) or less)
It will return to normal as you just continue scanning.
J
U
Indicates that a temporary error occurred during scanning.
The display will switch between either "J" or "U", and an
“error number”.
For information about the error details, refer to "Temporary
Errors" (page 102).
The display will return to ready ("1") if the [Scan/Stop] or
[Send to] button is pressed.
E
H
L
Indicates that a device error (alarm) occurred during
initialization or scanning.
The display will switch between either "E'", "H" or "L", and an
“alarm” number.
For information about the error details, refer to "Device
Errors" (page 102).
The display will return to ready ("1") if the [Scan/Stop] or
[Send to] button is pressed.
When this alarm occurs, turn the power off then back on.
If the problem still persists, contact your FUJITSU scanner
dealer or an authorized FUJITSU scanner service provider.
None The display switches off when the scanner enters power
saving mode.
Display Description

Fujitsu fi-6110 Specifications

General

Film scanning	No
Color scanning	Yes
Grayscale levels	1024
Input color depth	24 bit
Maximum scan size	216 x 355.6 mm
Optical scanning resolution	600 x 600 DPI
Flatbed scan speed (b/w, A4)	3 sec/page
Scanner type	Sheet-fed scanner
Sensor type	CCD
ISO A-series sizes (A0...A9)	A4, A5, A6
Maximum ISO A-series paper size	A4
Auto document feeder (ADF) input capacity	500 sheets
USB version	2.0
Standard interfaces	USB 2.0
Scan media weight	52 - 127 g/m²
Dimensions (WxDxH)	292 x 143 x 130 mm
Power requirements	100 - 240 V, 50/60 Hz
Image formats supported	JPG, TIF
Recommended media weight	80 g/m²
Compatible operating systems	Microsoft Windows 7 (32bit/64bit)/Vista (32bit/64bit), Windows Server 2003/2008/2008 R2 (32bit/64bit), Windows XP (32bit/64bit).
Power supply type	AC
Power consumption (standby)	5.36 W
Power consumption (typical)	28 W
Operating temperature (T-T)	42 - 95 °F
Operating relative humidity (H-H)	20 - 80 %
Bundled software	TWAIN, ISIS, ScandAll PRO, Adobe Acrobat, QuickScan Pro.

Weight and Dimensions

Depth	143 mm
Width	292 mm
Height	130 mm
Weight	3000 g