Fujitsu fi-6110 User Manual

Chapter 6 Daily Care
Appendix
Glossary
Introduction
Index
Contents
TOP
88
How to Load
Documents
Configuring the
Scan Settings
How to Use the
Operator Panel
Various Ways to
Scan
Troubleshooting
Replacing the
Consumables
Scanner
Overview
Daily Care
Operational
Settings
The inside of the scanner should be cleaned with a piece of
cloth/Cleaning Paper moistened with Cleaner F1, or a sheet of
Cleaning Wipe.
As the scanner continues to feed the documents, paper dust
will accumulate inside the scanner and it may cause scanning
errors.
As a guideline, clean the inside of the scanner every 1,000
sheets scanned. Note that this guideline varies depending on
the type of documents you scan. For instance, it may be
necessary to clean more frequently when you scan
documents on which the toner is not sufficiently fused.
1 Turn off the scanner and wait for at least 15 minutes.
For details, refer to "1.3 Turning the Power ON/OFF" (page 18).
2 Open the ADF.
For details, refer to "1.4 Opening/Closing the ADF" (page 19).
3 Clean the following locations with a cloth/Cleaning Paper
moistened with Cleaner F1, or a sheet of Cleaning Wipe.
6.3 Cleaning the Inside
z The glasses inside the ADF become very hot
when the scanner is being used.
When cleaning the inside of the scanner,
make sure to unplug the power cable and wait
for at least 15 minutes before you start
cleaning.
z When you perform cleaning, make sure that
the inside is free of foreign matter, and be
careful not to get your hand or the cloth
caught on the pick spring (metal part) as a
deformed pick spring (metal part) may cause
injury.
！！！
z Do not use water or mild detergent to clean the inside of the
scanner.
z It may take a long time to dry if an excessive amount of
Cleaner F1 is used. Moisten the cloth with moderate
quantity. Wipe off the cleaner completely to leave no
residue on the cleaned parts.
Be careful not to have your fingers caught
when the ADF closes.
Glass (×2)
*one on the opposite side
Pick Spring (metal part shown in gray)(×1)
Pick Roller (×1)
Ultrasonic Sensor (×2)
*one on the opposite side
Idler Roller (×4)
Feed Roller (×2)
Eject Roller (×2)
Pad Assy (×1)

Fujitsu fi-6110 Specifications

General

Film scanning	No
Color scanning	Yes
Grayscale levels	1024
Input color depth	24 bit
Maximum scan size	216 x 355.6 mm
Optical scanning resolution	600 x 600 DPI
Flatbed scan speed (b/w, A4)	3 sec/page
Scanner type	Sheet-fed scanner
Sensor type	CCD
ISO A-series sizes (A0...A9)	A4, A5, A6
Maximum ISO A-series paper size	A4
Auto document feeder (ADF) input capacity	500 sheets
USB version	2.0
Standard interfaces	USB 2.0
Scan media weight	52 - 127 g/m²
Dimensions (WxDxH)	292 x 143 x 130 mm
Power requirements	100 - 240 V, 50/60 Hz
Image formats supported	JPG, TIF
Recommended media weight	80 g/m²
Compatible operating systems	Microsoft Windows 7 (32bit/64bit)/Vista (32bit/64bit), Windows Server 2003/2008/2008 R2 (32bit/64bit), Windows XP (32bit/64bit).
Power supply type	AC
Power consumption (standby)	5.36 W
Power consumption (typical)	28 W
Operating temperature (T-T)	42 - 95 °F
Operating relative humidity (H-H)	20 - 80 %
Bundled software	TWAIN, ISIS, ScandAll PRO, Adobe Acrobat, QuickScan Pro.

Weight and Dimensions

Depth	143 mm
Width	292 mm
Height	130 mm
Weight	3000 g