Harman P35I User Manual

11
Save These Instructions 3-90-775R36_09/15
F. Factory Built Fireplace Installation
When installing the P35i Insert into a factory built wood
burning fireplace, several things need to be taken into
consideration.
The size of thereplace opening. Will the unitt intothe
opening? Some of the factory built replaces have metal
smokeshieldsinsidethetopthatcanberemovedtogain
height. Keep in mind that anything removed from the factory
builtreplacemustbeattachedtothereplacewithametal
wire. Floor protection guidelines, as listed previously, must
also be followed.
Themanufacturedreplacemaynotbealteredbeyondthe
exceptions listedbelow. Never remove masonry bricks or
mortarfromanexistingreplace.
Thefollowingmodicationsarepermissible:
• Removalofthedamperorlockinopenposition
• Removalofsmokeshelforbafe
• Removal of andirons or ember catchers
• Removal of log grate
• Removal of view screen or curtain
• Removal of doors
• Externaltrimpieces,thatdonotaffecttheoperationof
the replace, may be removed providing they can be
stored onor within the replacefor reassembly if the
insert is removed.
• Ifthehearthextensionislowerthanthereplaceopening,
theportionoftheinsertextendingontothehearthmust
be supported.
• Final approval of this type of installation is contingent
upon the authority having jurisdiction.
• Kit #1-00-674205 must be used when using this
installation method.
Note: If the Harman
®
P35iInsertisinstalledintoafactorybuiltwoodburningreplace,thislabel(Harman
®
part#3-90-00675)
MUST beattachedtothealteredreplace.
Thefactorybuiltchimneymustbe listed per UL127(US)
and meet type HT requirements of UL103 (US). Factory
BuiltreplacechimneystestedtoUL127-98maybe,atthe
replacemanufacturersoption,testedtothesamecriteria
as UL 103HT requirements. If the chimney is not listed as
meetingHTrequirements,orifthefactorybuiltreplacewas
tested prior to 1998, a full height listed chimney liner must be
installedfromtheapplianceuecollartothechimneytop.
Linermustmeethightemperature(2100°F)perUL1777(US).
Thelinermustbesecurelyattachedtoboththeuecollar
and the chimney cap. To prevent room air passage to the
chimneycavityofthereplace,sealthedamperareaaround
thechimneylinerwithberglassbatting.
Hearth must be constructed to
the proper height and finished
with a non-combustible
material.
IN CANADA: This replace insert
must be installed with a continuous
chimney liner of a minimum 3" diameter
extending from the insert to the top of
the chimney. The chimney liner must
conform to the Class 3 requirements
ofCAN/ULC-S635,StandardforLining
Systems for Existing Masonry or
Factory Built Chimneys and Vents, or
CAN/ULC-S640, Standard for Lining
Systems for New Masonry Chimneys.
Whenusingsingle-wallventingor
ex,thissectionofventingmustbe
wrappedwithanon-combustible
insulationtopreventexcess
temperatureswithinthereplace
and on the fuel hopper.
Additionally,thereboxooroftheZCWoodorGasFireplacemayberemoveddowntotheoutermetalshellofthereplace
ifkit1-00-574305 isused.The kitincludesinstallation instructions andallmaterials neededtoremovethe reboxoor
andstillmaintainasafe,compliantinstallation.Becertaintocontactlocalcodeenforcementofcialsbeforebeginningany
modications,astheymaynotbereversibleinmanycases.

Harman P35I Specifications

General

Brand	Harman
Model	P35I
Category	Indoor Fireplace
Language	English