EasyManuals Logo
Home>Manitowoc>Construction Equipment>Grove YB5520

Manitowoc Grove YB5520 User Manual

Manitowoc Grove YB5520
144 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #51 background imageLoading...
Page #51 background image
Grove Published 07-06-2017, Control # 406-03 2-39
CD5520/YB5520 OPERATOR MANUAL SAFETY INFORMATION
2
If applicable to your crane, frequently check all air tanks for
water in freezing weather.
If applicable to your crane, always handle propane tanks
according to the supplier’s instructions.
Never store flammable materials on the crane.
If cold weather starting aids are provided on your crane, use
them. The use of aerosol spray or other types of starting
fluids containing ether/volatiles can cause explosions or fire.
TEMPERATURE EFFECTS ON HOOK
BLOCKS
The following information applies to Gunnebo Johnston
crane hook blocks:
Never use a hook block in extreme tempera-
tures...Sudden failure can occur.
Hook blocks shall not be heated above 82°C
(180°F). Hook Block Working Load Limit is valid
between 82°C (180°F) and service temperature
given on the identification tag with normal lifting
precautions.
Additional lifting precautions are required below the
service temperature given on the identification tag
because cold temperature begins to affect the hook
block material properties.
Lifting above 75% of the Working Load Limit (WLL),
at temperatures between the service temperature
given on the identification tag and -40°C (-40°F),
must (be) done at a slow and steady rate to avoid
stress spikes common in normal hoisting dynamics.
75% of the WLL must not be exceeded, when lifting
in temperatures below -40°C (-40°F).
TEMPERATURE EFFECTS ON HYDRAULIC
CYLINDERS
Hydraulic oil expands when heated and contracts when
cooled. This is a natural phenomena that happens to all
liquids. The coefficient of expansion for API Group 1
hydraulic oil is approximately 0.00077 cubic centimeters per
cubic centimeter of volume for 1°C of temperature change
(0.00043 cubic inches per cubic inch of volume for 1°F of
temperature change). Thermal contraction will allow a
cylinder to retract as the hydraulic fluid which is trapped
in the cylinder cools.
The change in the length of a cylinder is proportional to the
extended length of the cylinder and to the change in
temperature of the oil in the cylinder. For example, a cylinder
extended 7.6 m (25 ft) in which the oil cools 15.5°C (60°F)
would retract approximately 196 mm (7 3/4 in) [see Table 2-9
and Table 2-8]. The rate at which the oil cools depends on
many factors and will be more noticeable with a larger
difference in oil temperature verses the ambient
temperature.
Thermal contraction coupled with improper lubrication or
improper wear pad adjustments may, under certain
conditions, cause a “stick-slip” condition in the boom. This
“stick-slip” condition could result in the load not moving
smoothly. Proper boom lubrication and wear pad adjustment
is important to permit the boom sections to slide freely. Slow
movement of the boom may be undetected by the operator
unless a load is suspended for a long period of time. To
minimize the effects of thermal contraction or “Stick-slip” it is
recommended that the telescope control lever is activated
periodically in the extend position to mitigate the effects of
cooling oil.
If a load and the boom is allowed to remain stationary for a
period of time and the ambient temperature is cooler than the
trapped oil temperature, the trapped oil in the cylinders will
cool. The load will lower as the telescope cylinder(s) retracts
allowing the boom to come in. Also, the boom angle will
decrease as the lift cylinder(s) retracts causing an increase
in radius and a decrease in load height.
This situation will also occur in reverse. If a crane is set up in
the morning with cool oil and the daytime ambient
temperature heats the oil, the cylinders will extend in similar
proportions.
Table 2-8 and Table 2-9 have been prepared to assist you in
determining the approximate amount of retraction/extension
that may be expected from a hydraulic cylinder as a result of
change in the temperature of the hydraulic oil inside the
cylinder. The chart is for dry rod cylinders. If the cylinder rod
is filled with hydraulic oil, the contraction rate is somewhat
greater.
NOTE: Operators and service personnel must be aware
that load movement, as a result of this phenomena,
can be easily mistaken as leaking cylinder seals or
faulty holding valves. If leaking seals or faulty
holding valves are suspected to be the problem,
refer to Service Bulletin dealing with testing
telescope cylinders. (Service Bulletin 98-036
applies to TMS700 and Service Bulletin G06-005A
applies to RT890 and RT9130.
Reference Only

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Manitowoc Grove YB5520 and is the answer not in the manual?

Manitowoc Grove YB5520 Specifications

General IconGeneral
BrandManitowoc
ModelGrove YB5520
CategoryConstruction Equipment
LanguageEnglish

Related product manuals