Mindray Passport V Service Manual

131 pages

To Next Page

To Previous Page

Passport V™ Service Manual 0070-10-0705 6 - 5

Preventative Maintenance Care and Cleaning of SpO

Sensors

6.4 Care and Cleaning of SpO

Sensors

NOTE: Refer to the individual instruction sheets that are packaged

with each sensor.

1. Check sensors and cables daily for signs of damage. Replace as required.

2. Sensors should be cleaned before and after each new patient.

3. Wipe the patient contact area using a soft cloth with mild soap and water solution or

isopropyl alcohol. Hydrogen peroxide can be used to remove dried blood.

4. Allow the sensor to completely dry before using.

CAUTION: When cleaning sensors, do not use excessive amounts of

liquid. Wipe the sensor surface with a soft cloth dampened

with cleaning solution. Do not attempt to sterilize.

6.4.1 Cleaning and Re-use of a Nellcor

Sensor

Sensors may be reattached to the same patient if the emitter and detector windows are clear

and the adhesive still adheres to the skin. The adhesive can be partially rejuvenated by

wiping with an alcohol wipe and allowing the sensor to thoroughly air dry prior to

replacement on the patient.

Do not immerse any Oxisensor

, OxiMax

, Durasensor

, Oxiband

, or Duraform

oxygen

transducers, the Nellcor

RS-10 or Max-Fast

oxygen transducers, or any Nellcor

adhesive

in water or cleaning solution. Clean Durasensor

, Oxiband

, and Duraform

oxygen

transducers, and the Nellcor

RS-10 or Max-Fast

oxygen transducers by wiping with a

disinfectant such as a solution containing 70% alcohol. Do not sterilize by irradiation, steam,

or ethylene oxide. Use a new Oxiband

adhesive wrap or FORM-A adhesive bandage for

each patient. Do not re-sterilize Oxisensor

or OxiMax

oxygen transducers.

Other manuals for Mindray Passport V

Operating Instructions288 pages

Need help?

Do you have a question about the Mindray Passport V and is the answer not in the manual?

Mindray Passport V Specifications

General

Brand	Mindray
Model	Passport V
Category	Health Care Products
Language	English

Summary

Foreword

Warnings, Cautions, and Notes

General guidelines and important safety information for users and technicians.

Warnings

Alerts regarding potential serious risks, including electrical shock hazards.

Cautions

Notes on using the device with care to avoid adverse effects or damage.

Theory of Operation

Repair Information

Safety Precautions

Essential safety guidelines and warnings for personnel performing repairs.

Troubleshooting Guidelines

Methods and advice for diagnosing and resolving instrument problems effectively.

Disassembly Instructions Overview

General steps and precautions before disassembling the patient monitor unit.

Troubleshooting Menus

ECG Troubleshooting

Common ECG messages, reasons, and solutions for troubleshooting.

NIBP Troubleshooting

Common NIBP messages, reasons, and solutions for troubleshooting.

SpO2 Troubleshooting

Common SpO2 messages, reasons, and solutions for troubleshooting.

Temperature Troubleshooting

Common temperature messages, reasons, and solutions for troubleshooting.

Resp Troubleshooting

Common respiration messages, reasons, and solutions for troubleshooting.

IBP Troubleshooting

Common IBP messages, reasons, and solutions for troubleshooting.

CO2 Troubleshooting

Common CO2 messages, reasons, and solutions for troubleshooting.

Gas Module Troubleshooting

Common gas module messages, reasons, and solutions for troubleshooting.

Installation Menu

Installation Mode

Procedure for entering and configuring the monitor's installation settings.

Advanced Installation Setup Menu

Configuration options for network, IP address, and other advanced settings.

Calibration Procedure

Warnings and Guidelines

Safety precautions and general guidelines for performing calibration procedures.