To Next Page

To Previous Page

English-68

PBP3 PICTURE 1: OPTION (TMDS)

Picture 3

HDMI1 HDMI2 HDMI3 MP DisplayPort2 DisplayPort1 OPTION

Connector

HDMI IN1 HDMI IN2 HDMI IN3 –

DisplayPort

IN2

DisplayPort

IN1

Option board

slot (SLOT2

(DP))

Option board

slot (SLOT2

(DP+TMDS))

Option board

slot (SLOT2

(TMDS))

Picture 2 Connector

TERMINAL

SETTINGS*

MODE

– – – 2CH MODE 1

Picture 1: OPTION (TMDS)

HDMI1 HDMI IN1

MODE 1 Yes No Yes No Yes No Yes Yes Yes No No Yes

MODE 2 No No No No No No No Yes Yes No No Yes

HDMI2 HDMI IN2

MODE 1 Yes No Yes No Yes No Yes Yes Yes No No Yes

MODE 2 No No No No No No No Yes Yes No No Yes

HDMI3 HDMI IN3

MODE 1 Yes No Yes No Yes No Yes Yes Yes No No Yes

MODE 2 No No No

No No No No Yes Yes No No Yes

MP – MODE 1 Yes No Yes No Yes No Yes Yes Yes No No Yes

DisplayPort2 DisplayPort IN2 – Yes No Yes No Yes No Yes Yes Yes No No Yes

DisplayPort1 DisplayPort IN1 – Yes No Yes No Yes No Yes Yes Yes No No Yes

OPTION

Option board slot

(SLOT2 (DP))

– No No No No No No No No No No No No

Option board slot

(SLOT2 (DP+TMDS))

2CH No No No No No No No No No No No No

Option board slot

(SLOT2 (TMDS))

MODE 1 Yes No Yes No Yes No Yes Yes Yes No No Yes

*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)

PICTURE NUMBER: 4 PICTURES

Only one input signal can be selected from within a group.

One of ﬁve groups is displayed on each screen. The same group can be selected more than once.

Group A Group B Group C Group D Group E

DisplayPort1

OPTION (DP)

DisplayPort2

HDMI1

HDMI2

HDMI3

HDMI1

HDMI2

HDMI3

OPTION (TMDS)

NOTE: HDMI1/HDMI2/HDMI3 TERMINAL SETTINGS is MODE1 only.

OPTION (DP) and OPTION (TMDS) cannot be selected at the same time (Can be choose either one).

Video out

Main picture

DisplayPort1 DisplayPort2 HDMI1 HDMI2 HDMI3 OPTION MP

Connector

DisplayPort

IN1

DisplayPort

IN2

HDMI

IN1

HDMI

IN2

HDMI

IN3

Option board slot

(SLOT2 (DP))

Option board slot

(SLOT2 (HDMI))

DisplayPort Yes

No No No No

Yes

No No

When the monitor outputs a signal from the DisplayPort out, please select input signal DisplayPort1 or OPTION.

This monitor’s signal output function supports contents, which is protected by HDCP. In this case, up to 3 monitors are connectable.

When using an option, please set SLOT2 CH SETTING to 1CH then set SLOT2 CH SELECT to DisplayPort (See page 45).

NOTE: To output a signal from the DisplayPort out, some Slot2 type options are only available which have DisplayPort

signal out.

Questions and Answers:

Need help?

Do you have a question about the NEC MultiSync V984Q and is the answer not in the manual?

NEC MultiSync V984Q Specifications

General

Response time	8 ms
Display diagonal	98 \
Display brightness	350 cd/m²
Display technology	LED
Vertical scan range	24 - 85 Hz
Horizontal scan range	31.5 - 91.1 kHz
LED backlighting type	Direct-LED
Contrast ratio (typical)	1300:1
Display number of colors	1.073 billion colors
Display diagonal (metric)	247.82 cm
Active display area (W x H)	2158.9 x 1214.4 mm
Supported graphics resolutions	1920 x 1080 (HD 1080), 1920 x 2160, 3840 x 2160, 4096 x 2160
Orientation	Horizontal/Vertical
Product design	Digital signage flat panel
Placement supported	Indoor
Bezel width (bottom)	15.9 mm
Panel mounting interface	400 x 400, 600 x 400 mm
USB version	2.0
USB ports quantity	5
DisplayPorts quantity	3
Compatible memory cards	MicroSD (TransFlash), MicroSDHC
Ethernet LAN data rates	100 Mbit/s
VGA (D-Sub) input ports	0
Ethernet LAN (RJ-45) ports	2
Purpose	Universal
Operating hours (hours/days)	24/7
International Protection (IP) code	IP5X
Power consumption (standby)	0.5 W
Power consumption (typical)	380 W
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Certification	CE; EAC; EMC B; FCC; SASO; TÜV GS; UL/C-UL, CSA; VCCI
RMS rated power	20 W
Harmonized System (HS) code	85285210