16 – ENGLISH
LR
23
6.6.3.1 PROCEDURE A - Memorising ALL buttons of a
single transmitter (STANDARD mode or Mode 1)
To perform this procedure:
1. on the control unit: press and hold the [Radio
R
] but-
ton until the “LR” LED lights up
2. release the button [Radio
R
]
3. (within 10 seconds) on the transmitter to be memorised:
press and hold any button and wait until the “LR” LED
emits 3 long ashes (= memorisation completed correctly)
4. release the transmitter button.
l
After the 3 long ashes a further 10 seconds remain
to memorise an additional transmitter (if desired),
starting from step 3.
l
The “LR” LED can also emit the following signals: 1
fast ash, if the transmitter is already memorised, 6
ashes, if the transmitter’s radio encoding system
is not compatible with that of the control unit’s re-
ceiver, or 8 ashes, if the memory is full.
6.6.3.2 PROCEDURE B - Memorising a SINGLE BUTTON
of a transmitter (CUSTOM mode or Mode 2)
To perform this procedure:
1. choose the command to be paired with the relevant button
to be memorised:
– for no. 1 - “Step-by-Step” press the [Radio
R
] button
once
– for no. 2 - “AUX” press the [Radio
R
] button twice
– for no. 3 - “OPEN” press the [Radio
R
] button 3
times
– for no. 4 - “CLOSE” press the [Radio
R
] button 4
times
2. on the control unit: press and release the [Radio
R
]
button for a number of times corresponding to the desired
command, as shown near the command selected before-
hand at step 1.
3. (within 10 seconds) on the transmitter: press and hold
the button to be memorised and wait for the “LR” LED to
emit 3 long ashes (= memorisation completed correctly)
4. release the transmitter button.
l
After the 3 long ashes a further 10 seconds remain
to memorise an additional button (if desired), start-
ing from step 1.
l
The “LR” LED can also emit the following signals: 1
fast ash, if the transmitter is already memorised, 6
ashes, if the transmitter’s radio encoding system
is not compatible with that of the control unit’s re-
ceiver, or 8 ashes, if the memory is full.
6.6.3.3 PROCEDURE C - Memorising a transmitter by
means of another transmitter already memorised
(memorisation far from the control unit)
This procedure can be used to memorise a new transmitter by
means of a second transmitter, already memorised in the same
control unit. In this way, the new transmitter can receive the
same settings as those of the memorised transmitter. The user
does not have to intervene directly on the control unit’s [Radio
R
] button, as the procedure is simply carried out within the
control unit’s radius of reception.
To perform this procedure:
1. on the transmitter to be memorised: press and hold the
button to be memorised
2. on the control unit: after a few seconds (roughly 5) the
“LR” LED lights up
3. release the transmitter button
4. on the transmitter already memorised: press and slowly
release 3 times the memorised button to be copied
5. on the transmitter to be memorised: press and hold the
same button pressed at point 1 and wait for the “LR” LED
to emit 3 long ashes (= memorisation completed correct-
ly)
6. release the transmitter button.
l
The “LR” LED can also emit the following signals: 1
fast ash, if the transmitter is already memorised, 6
ashes, if the transmitter’s radio encoding system
is not compatible with that of the control unit’s re-
ceiver, or 8 ashes, if the memory is full.
6.6.3.4 PROCEDURE D - Deleting a single transmitter
(if memorised in Mode 1) or a single transmitter
button (if memorised in Mode 2)
To perform this procedure:
1. on the control unit: press and hold the [Radio
R
] but-
ton
2. after roughly 4 seconds, the “LR” LED will light up steady
(continue holding down the [Radio
R
] button
3. on the transmitter to be deleted from the memory:
press and hold a button (*) until the “LR” LED (on the con-
trol unit) emits 5 fast ashes (or 1 ash if the transmitter or
button is not memorised).
4. release the [Radio
R
] button.
(*) If the transmitter is memorised in Mode 1, any button
can be pressed and the control unit will delete the en-
tire transmitter. If the transmitter is memorised in Mode
2, it is necessary to press the memorised button to be
deleted. To delete further buttons memorised in Mode 2,
repeat the entire procedure for every button to be delet-
ed.
6.6.3.5 PROCEDURE E - Deleting ALL memorised
transmitters
To perform this procedure:
1. on the control unit: press and hold the [Radio
R
] but-
ton
2. after roughly 4 seconds, the “LR” LED will light up steady
(continue holding down the [Radio
R
] button
3. after roughly 4 seconds, the “LR” LED will turn off (contin-
ue holding down the [Radio
R
] button
4. when the “LR“ LED starts ashing, count 2 ashes and
prepare to release the button precisely during the 3rd
ash that follows
5. during the deletion process, the “LR” LED will ash rapidly
6. the “LR” LED will emit 5 long ashes to signal that the
deletion has been completed correctly.
To Next Page
Loading...
Need help?
General
