Nice MC424L User Manual

22 – ENGLISH
TECHNICAL SPECIFICATIONS
11
11 TECHNICAL SPECIFICATIONS
l
All technical specications stated in this section refer to an ambient temperature of 20°C (± 5°C). Nice S.p.A.
reserves the right to apply modications to the product at any time when deemed necessary, without altering
its functions and intended use.
Table 15
TECHNICAL SPECIFICATIONS
Description Technical specication
Mains power supply
Control unit MC424L: 230 Va ± 10% 50–60 Hz; fuse: 1A type T
Control unit MC424L/V1: 120 Va ± 10% 50–60 Hz; fuse: 2A type T
Control unit MC424L/AU01: 250 Va ± 10% 50–60 Hz; fuse: 1A type T
Maximum power input
170 W
Emergency power supply
congured for PS124 back-up batteries and for the Solemyo solar power kit
Maximum motor current
3 A (with “level 6” amperometric device intervention)
Services power output 24 Vc maximum current 200 mA (the voltage may vary between 16 V and 33 Vc)
Phototest output 24 Vc maximum current 100 mA (the voltage may vary between 16 V and 33 Vc)
Warning light output
for 24 V c warning lights, maximum power 25 W (the voltage may vary between 16 V and 33 Vc);
for Nice ELDC and EL24 warning lights
Electric lock output
for 24 V c lamps, maximum power 5 W (the voltage may vary between 16 V and 33 V c) or for 12 V
a electric locks, 15 VA
ALT (STOP) input
for NC contacts or 8.2 kΩ xed resistor +/– 25%
Work time
measured automatically
Pause time
settable
Discharge time
settable
Leaf opening delay
settable
Leaf closing delay
measured automatically
1st motor output
for WINGO motors (WG2024, WG3524, WG4024, WG5024), TOO (TOO3024, TOO4524), SFAB
(XME2024)
2nd motor output
for WINGO motors (WG2024, WG3524, WG4024, WG5024), TOO (TOO3024, TOO4524), SFAB
(XME2024)
Max length of cables
power supply: 30 m
Solemyo solar kit power supply: 3 m
motors: 10 m
other inputs/outputs: 30 m
warning light: 10 m
OGI: 30 m
electric lock: 10 m
antenna: 20 m (recommended below 3 m)
Radio receiver
“SM”-type connector for SMXI, SMXIS, OXI receivers (Mode 1 and Mode 2)
Operating temperature
from –20°C to +55°C
Protection rating
IP 54 (with container intact)
Dimensions (mm)
310 x 232 x H 122
Weight (kg)
4,1
CONFORMITY
12
12 CONFORMITY
EU Declaration of Conformity
and declaration of incorporation of “partly completed machinery”
Note - The contents of this declaration correspond to declarations in the ofcial document deposited at the registered ofces of Nice S.p.a. and in particular to the last revision available before
printing this manual. The text herein has been re-edited for ed
itorial purposes. A copy of the original declaration can be requested from Nice S.p.a. (TV) I.
Number:
296/MC424 Rev: 5 Language: EN
Manufacturer’s Name:
Nice s.p.a.
Address:
Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy
Authorized Person to constitute
technical documentation:
Nice s.p.a.
Type of product:
Comand central a 2 motor 24V dc
Model/Type:
MC424, MC424L
Accessories:
Refer to the catalog
The
undersignedRobertoGriffa,intheroleofChiefExecutiveOfcer,declaresunderhissoleresponsibilitythattheproductdescribedabovecomplieswiththe
provisions
laid
downinthefollowingdirectives:
•Directive
2014/30/EU(EMC),accordingtothefollowingharmonizedstandards:EN61000-6-2:2005,EN61000-6-3:2007+A1:2011
The
productalsocomplieswiththefollowingdirectivesaccordingtotherequirementsenvisagedfor“partlycompletedmachinery”(AnnexII,part1,sectionB):
•
Directive 2006/42/EC of the EUROPEAN PARLIAMENT AND COUNCIL of 17 May 2006 related to machinery and amending the Directive 95/16/EC (recast).
It
isherebystatedthattherelevanttechnicaldocumentationhasbeencompiledinaccordancewithannexVIIBofDirective2006/42/ECandthatthefollowing
essential
requirements
havebeenfullled:1.1.1-1.1.2-1.1.3-1.2.1-1.2.6-1.5.1-1.5.2-1.5.5-1.5.6-1.5.7-1.5.8-1.5.10-1.5.11
The
manufacturerundertakestotransmittothenationalauthorities,inresponsetoareasonedrequest,therelevantinformationonthe“partlycompletedmachinery“,
while
maintaining full rights to the related intellectual property.
Should
the“partlycompletedmachinery”beputintoserviceinaEuropeancountrywithanofciallanguageotherthanthatusedinthisdeclaration,theimporteris
obliged
to arrange for the relative translation to accompany this declaration.
The
“partlycompletedmachinery”mustnotbeuseduntilthenalmachineinwhichitisincorporatedisinturndeclaredascompliant,ifapplicable,withtheprovisions
of
directive 2006/42/EC.
The
productalsocomplieswiththefollowingstandards:
EN 60335-1:2012+A11:2014, EN 62233:2008, EN 60335-2-103:2015
Oderzo, 05/09/2017
Ing. Roberto Griffa
(ChiefExecutive
Ofcer)

Nice MC424L Specifications

General

Brand	Nice
Model	MC424L
Category	Control Unit
Language	English