74
Chapter 4 Using the XV-5050 Effects
Multi-Effects Settings
Chorus Settings
Reverb Settings
Parameter
Value Description
EFFECTS MFX
Source
Multi-Effects Source PERFORM, PART 1–16 Selects the Multi-effects parameter settings that will be used by the Performance. If you
wish to use the Performance settings, select PERFORM. If you wish to use the settings of
the Patch/Rhythm Set assigned to one of the Parts, select the Part number.
Type Multi-Effects Type 00 (THROUGH) –90 Use this parameter to select from among the 90 available Multi-effects.
* For details on Multi-effects parameters, refer to “Multi-Effects Parameters” (p. 75).
Ctrl Src 1–4 Multi-Effects Control
Source 1–4
OFF, CC01–31, CC33–95,
BEND, AFTER, SYS1–4
Selects the Control Source to be used for changing the Multi-effects parameters.
Ctrl Dest 1–4 Multi-Effects Control
Destination 1–4
Refer to “Multi-Effects
Parameters” (p. 75).
Selects the Multi-effects parameter to be controlled using Ctrl Src 1–4. The parameters
that can be selected depend on which type of Multi-effects is set to MFX Type.
Ctrl Sens 1–4 Multi-Effects Control
Sensitivity 1–4
-63– +63 If you wish to modify the selected parameter in a positive (+) direction—i.e., a higher val-
ue, toward the right, or faster, etc.—from its current setting, select a positive (+) value. If
you wish to modify the selected parameter in a negative (-) direction—i.e., a lower value,
toward the left, or slower, etc.—from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
Output Asgn Multi-Effects Output
Assign
OUTPUT A/B Adjusts the output destination of the sound that has passed through the Multi-effects.
OUTPUT A:
Output to the OUTPUT A (MIX) jacks in stereo.
OUTPUT B:
Output to the OUTPUT B jacks in stereo.
Output Dry
Send
Multi-Effects Dry
Send Level
0–127 Adjusts the volume of the sound that has passed through the Multi-effects.
Output Cho
Send
Multi-Effects Chorus
Send Level
0–127 Adjusts the amount of Chorus for the sound that passes through Multi-effects. If you
don’t want to add the Chorus effect, set it to 0.
Output Rev
Send
Multi-Effects Reverb
Send Level
0–127 Adjusts the amount of Reverb for the sound that passes through Multi-effects. If you
don’t want to add the Reverb effect, set it to 0.
Parameter Value Description
EFFECTS CHO
Source
Chorus Source PERFORM, PART 1–16 Selects the Chorus parameter settings that will be used by the Performance. If you wish
to use the Performance settings, select PERFORM. If you wish to use the settings of the
Patch/Rhythm Set assigned to one of the Parts, select the Part number.
Type Chorus Type OFF, CHORUS, DELAY,
GM2 CHORUS
Selects either Chorus or Delay.
* For details on Chorus parameters, refer to “Chorus Parameters” (p. 102).
Output Asgn Chorus Output Assign OUTPUT A/B Selects the pair of OUTPUT jacks to which the Chorus sound is routed when Chorus
Output Select is set to MAIN or MAIN+REV.
OUTPUT A:
Output to the OUTPUT A (MIX) jacks in stereo.
OUTPUT B:
Output to the OUTPUT B jacks in stereo.
Level
Chorus Level 0–127 Adjusts the volume of the sound that has passed through chorus.
Out Select Chorus Output Select MAIN, REV,
MAIN+REV
Specifies how the sound routed through Chorus will be output.
MAIN:
Output to the OUTPUT jacks in stereo.
REV:
Output to Reverb in mono.
MAIN+REV:
Output to the OUTPUT jacks in stereo, and to Reverb in mono.
Parameter
Value Description
EFFECTS REV
Source
Reverb Source PERFORM, PART 1–16 Selects the Reverb parameter settings that will be used by the Performance. If you
wish to use the Performance settings, select PERFORM. If you wish to use the settings
of the Patch/Rhythm Set assigned to one of the Parts, select the Part number.
Type Reverb Type OFF, REVERB, SRV ROOM,
SRV HALL, SRV PLATE,
GM2 REVERB
Selects the type of Reverb.
* For details on Reverb parameters, refer to “Reverb Parameters” (p. 103).
Output Asgn Reverb Output Assign OUTPUT A/B Specifies how the sound routed through Reverb will be output.
OUTPUT A:
Output to the OUTPUT A (MIX) jacks in stereo.
OUTPUT B:
Output to the OUTPUT B jacks in stereo.
Level
Reverb Level 0–127 Adjusts the volume of the sound that has passed through Reverb.
XV-5050_e.book 74 ページ ２００３年６月２７日 金曜日 午後３時１４分
To Next Page
Loading...
Need help?
General