Sony TA-AX2 User Manual

TAPE RECORDING AND TAPE COPY
SPECIFICATIONS
TO RECORD
OSelect the program to be recorded with the function switches.
©Start the program and set the tape recorder in ttie record mode.
Amplifier section
Continuous RMS power output
(Less than 0.07%
THD, both channels
driven simultaneously)
PHONO
Power bandwidth (IHF)
Harmonic distortion
Intermodulation (IM) distortion
(60 Hz : 7 kHz = 4 : 1)
Frequency response
At 1 kHz
30 + 30 watts (8 ohms)
At 20 Hz - 20 kHz
25 + 25 watts (8 ohms)
According to DIN 45500
25 + 25 watts (8 ohms)
15 Hz - 35 kHz
Less than 0.07% at rated output
Residual noise
Damping factor
Inputs
Less than 0.07% at rated output
PHONO : RIAA equalization curve ±0.5 dB
TUNER, TAPE 1, 2 : 10 Hz - 45 kHz ±1 dB
Less than 140 jj V (8 ohms, network A)
30 (8 ohms, 1 kHz)
• The VOLUME, BALANCE, and TONE controls and the LOW
FILTER and LOUDNESS switches have no effect on recording.
• Even if your tape recorder has separate record and playback
heads, you can't momitor the recording results.
Outputs
Sensitivity Impedance
Maximum input
capability (1 kHz)
S/N (weighting
network, input level)
PHONO 2.5 mV
50 kQ
150 mV
75 dB
TUNER
TAPE 1, 2
150 mV
50 kQ —
95 dB
TO COPY
If you have two tape recorders, you can copy a taped program from
tape recorder 1 (connected to TAPE 1 inputs) to tape recorder 2
(connected to REC OUT 2 outputs), and vice versa.
For copying from tape recorder 1 to tape recorder 2
O Insert the recorded tape into the tape recorder 1 and a blank tape
into the tape recorder 2.
© Press the TAPE 1 switch.
© Adjust the recording level of tape recorder 2.
Start the playback of tape recorder 1 and the recording of tape
recorder 2. Copying will begin.
Tone controls
Loudness (att. 30 dB)
Low filter
REC OUT 1, 2
Voltage 150 mV
Impedance 10 kilohms
SPEAKER A, B
Type 1 and Type 2 : Accepts speakers of 8 to
16 ohms.
Type 3 : Accepts speakers of 4 to 16 ohms.
HEADPHONES
Accepts low and high impedance
headphones.
BASS
±8 dB at 100 Hz
TREBLE
±8 dB at 10 kHz
+ 8 dB at 100 Hz
6 dB/octave attenuation below 50 Hz
General
System
Power requirements
Power consumption
Demensions
Weight
Quasi-complementary symmetry power amplifier
(SEPP OTL)
Type 1 (for European countries) : 220 V ac,
50/60 Hz
Type 2 (for the United Kingdom) : 240 V ac,
50/60 Hz
Type 3 (for other countries) : 120, 220
or 240 V ac adjustable, 50/60 Hz
Type 1 and 3 : 64 watts
Type 2 : 230 watts
Approx. 430 X 55 X 295 mm (w/h/d)
(17 X 2 1 /« X 11 ! /| inches)
including projecting parts and controls
Approx. 5.1 kg (11 lbs 4 oz) net
Approx. 5.8 kg (12 lbs 13 oz) in shipping carton
While the information given is true at the time of printing, small production
changes in the course of our company ’ s policy of improvement through
research and design might not necessarily be indicated in the specifications.
We would ask you to check with your appointed Sony dealer if clarification on
any point is required.
• For copying from tape recorder 2 to tape recorder 1, depress the
TAPE 2 switch and follow the same procedure.
10

Sony TA-AX2 Specifications

General

Brand	Sony
Model	TA-AX2
Category	Amplifier
Language	English