Trane Airfinity XL IH190 User Manual

RT-SVX060D-GB
46
4 UNT-PRC002-GB
Technical Data
FWD 08 12 20 30 45
Power supply (V/Ph/Hz) 230/1/50
Capacities
Cooling capacity on water (1) (kW) 5,2 8,3 15 18,8 30,1
Heating capacity on water (2) (kW) 6,3 11,9 18,9 20,9 38,2
Fan motor (type) 2 x direct drive centrifugal
Fan power input (3) (kW) 0,23 0,46 0,65 1,04 1,51
Current amps (3) (A) 1,1 2,2 3,1 4,7 5,5
Start-up amps (A) 3,2 5,5 9,3 14,1 16,5
Air flow
minimum (m
3
/h) 490 980 1400 1800 2700
nominal (m
3
/h) 820 1650 2300 3000 4500
maximum (m
3
/h) 980 1970 2600 3600 5400
Main coil
Water entering/leaving connections (type) ISO R7 rotating female
(Dia) 3/4" 3/4" 1 1/2" 1 1/2" 1 1/2"
Electric heater (accessory for blower only)
Electric power supply (V/Ph/Hz) 230/1/50 230/1/50 or 400/3/50 400/3/50 400/3/50 400/3/50
Heating capacity (kW) 2/4 8 10 12 12
Hot water coil (accessory for blower only)
Heating capacity (4) (kW) 6,3 12 17,4 22,4 34,5
G2 filter (filter box accessory)
Quantity 2 2 2 2 2
Dimensions ( LxWxth) (mm) 386x221x8 486x271x8 586x321x8 586*421*8 586*621*8
G4 filter (filter box accessory)
Quantity - 2 2 2 2
Dimensions ( LxWxth) (mm) - 486x264x48 586x314x48 586*414*48 586*614*48
Condensate pump (accessory) (type) Centrifugal
Water flow - lift height (l/h - mm) 24 - 500
Not available for FWD30 and FWD45
Sound level (L/M/H speed)
Sound pressure level (5) (dB(A)) 36/40/43 38/41/44 46/50/53 47/52/57 47/52/58
Sound power level (5) (dB(A)) 46/50/53 48/51/54 56/60/63 57/62/67 57/62/68
Unit dimensions
Width x Depth (mm) 890 x 600 1090 x 710 1290 x 820 1290 x 970 1290 x 1090
Height (mm) 250 300 350 450 650
Shipped unit dimensions
Width x Depth (mm) 933 x 644 1133 x 754 1333 x 864 1333 x 1008 1333*1133
Height (mm) 260 310 360 460 660
Weight (kg) 32 46 61 76 118
Colour galvanised steel
Recommended fuse size
Unit alone (aM/gI) (A) 8/16 8/16 8/16 8/25 8/25
Unit with electric heater (gI) (A) 16 (2kW),25 (4kW) 40 (230V),3*16 (400V) 3*20 3*25 3*25
(1) Conditions: Water entering/leaving temperature: 7/12 °C, Air inlet temperature 27/19°C DB/WB - Nominal air flow
(2) Conditions: Water entering/leaving temperature: 50/45 °C, Air inlet temperature 20°C DB - Nominal air flow
(3) At high speed with nominal air flow.
(4) Water entering/leaving temperature 90/70 °C, air inlet temperature 20 °C DB, Nominal air flow.
(5) A rectangular glass wool duct 1m50 long is placed on the blower.The measurement is taken in the room containing the blower unit.
Heat exchanger operating limits:
FWD:
*water temperature: max 100° C
*absolute service pressure: min 1 bar/max 11 bars
Accessories - Hot water coil:
*water temperature: min. +2° C/max. 100° C
*absolute service pressure: min 1 bar/max 11 bars
Test Procedures
Operating checklist before start-up
• Review submittals for rooftop and accessories as
well as main wiring diagrams and options shipped
with the unit
• Unit is level, with sufcient clearance all round
• Duct network is correctly sized according to the unit
conguration, insulated, and water-tight
• Condensate drainage line is correctly sized,
equipped with a trap, and sloped
• Filters are in position, of correct size and quantity
and clean
• Wiring is correctly sized and connected in
accordance with wiring diagrams
• Power supply lines are protected by recommended
fuses and correctly earthed
• Thermostat is correctly wired and positioned
• Unit is checked for refrigerant charge and leaks
• Indoor and outdoor fans rotate freely and are xed
on shafts
• Supply fan rotation speed is set
• Access panels and doors are replaced to prevent air
entering and risks of injury
• When ball valve is present on the refrigerant suction
line, to check if the valve is open before starting the
unit.
WARNING! If any operating checks must be performed
with the unit operating, it is the technician’s
responsibility to recognize any possible hazards and
proceed in a safe manner. Failure to do so could result
in severe personal injury or death due to electrical shock
or contact with moving parts.
Power-up initialization
CAUTION! Before proceeding with any test procedure or
operation, make sure that crankcase heaters have been
energized for at least 8 hours.
Starting the unit in cooling mode
Before start-up, ensure that all power cables are
tightened.
Verify that the unit airow rate is adjusted.
Operating pressures
After the unit has operated in cooling mode for a short
period of time, install pressure gauges on the gauge
ports of the discharge and suction line valves.
Note: Always route refrigerant hoses through the port
hole provided and ensure that the compressor access
panel is in place.
Final installation checklist
• Are all power cables tightened?
Check torque of power cables contact !
• Is the condenser fan and indoor blower operating
correctly, i.e. correct rotation and without undue
noise?
• Are the compressors operating correctly and has the
system been checked for leaks?
• Have the voltage and running currents been checked
to determine if they are within limits?
• Have the air discharge grilles been adjusted to
balance the system?
• Has the ductwork been checked for air leaks and any
condensation?
• Has the air temperature rise been checked?
• Has the indoor airow been checked and adjusted if
necessary?
• Has the unit been checked for tubing and sheet metal
rattles or any unusual noises?
• Are all covers and panels in place and properly
fastened?
To keep the unit operating safely and efciently, the
manufacturer recommends that a qualied service
technician check the entire system at least once each
year, or more frequently if conditions warrant.
Upon power initialization, the control performs self-
diagnostic checks to insure that all internal controls
are functioning. It checks the conguration parameters
against the components connected to the system.
Operation

Trane Airfinity XL IH190 Specifications

General

Brand	Trane
Model	Airfinity XL IH190
Category	Chiller
Language	English