Manual Manual 37223E 37223E easYgen-3000 easYgen-3000 Series Series (Package (Package P1) P1) - - Genset Genset ControlControl
Page Page 30/67 30/67 © © WoodwardWoodward
Voltage Measuring: MainsVoltage Measuring: Mains
LL11
LL22
LL33
NN
M
M
aa
ii
nn
ss
vv
oo
ll
tt
aa
gg
ee
((
pp
hh
aa
ss
ee
vv
oo
ll
tt
aa
gg
ee
))
MMCCBB
N / VcomN / Vcom
L1 / VaL1 / Va
L2 / VbL2 / Vb
L3 / VcL3 / Vc
2121
2222
2323
2424
2525
2626
2727
2828
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
100 Vac100 Vac
400 Vac400 Vac
optionaloptional
Figure 6-15: Voltage measuring - mainsFigure 6-15: Voltage measuring - mains
Terminal Terminal Description Description AA
maxmax
2121
Mains voltage - phase L1 / VaMains voltage - phase L1 / Va
100 100 Vac Vac 2.5 2.5 mm²mm²
22 22 400 400 Vac Vac 2.5 2.5 mm²mm²
2323
Mains voltage - phase L2 / VbMains voltage - phase L2 / Vb
100 100 Vac Vac 2.5 2.5 mm²mm²
24 24 400 400 Vac Vac 2.5 2.5 mm²mm²
2525
Mains voltage - phase L3 / VcMains voltage - phase L3 / Vc
100 100 Vac Vac 2.5 2.5 mm²mm²
26 26 400 400 Vac Vac 2.5 2.5 mm²mm²
2727
Mains voltage - phase N / Mains voltage - phase N / VcomVcom
100 100 Vac Vac 2.5 2.5 mm²mm²
28 28 400 400 Vac Vac 2.5 2.5 mm²mm²
Table 6-10: Voltage measuring - terminal assignment Table 6-10: Voltage measuring - terminal assignment - mains voltage- mains voltage
NOTE
NOTE
If parameter 1803 ("Mains PT seIf parameter 1803 ("Mains PT secondary rated volt.", refer to Configuration Manual 37224) is configuredcondary rated volt.", refer to Configuration Manual 37224) is configured
with a value between 50 and 130 V, the 100 V input terminals must be used for proper measurement.with a value between 50 and 130 V, the 100 V input terminals must be used for proper measurement.
If parameter 1803 ("Mains PT seIf parameter 1803 ("Mains PT secondary rated volt.", refer to Configuration Manual 37224) is configuredcondary rated volt.", refer to Configuration Manual 37224) is configured
with a value between 131 and 480 V, the 400 V input terminals must be used for proper measurement.with a value between 131 and 480 V, the 400 V input terminals must be used for proper measurement.
NOTE
NOTE
If the easYgen is intended to If the easYgen is intended to be operated in parallel with the be operated in parallel with the mains, the mains voltage measuring in-mains, the mains voltage measuring in-
puts must be connected. If an puts must be connected. If an external mains decoupling is performed, jumpers between busbar andexternal mains decoupling is performed, jumpers between busbar and
mains voltage measuring inputs may be installed.mains voltage measuring inputs may be installed.
To Next Page
Loading...
Need help?
General
