Manual Manual 37223E 37223E easYgen-3000 easYgen-3000 Series Series (Package (Package P1) P1) - - Genset Genset ControlControl
Page Page 50/67 50/67 © © WoodwardWoodward
Relay OutputsRelay Outputs
((LogicsManager
LogicsManager))
≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡
≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡
AA
BB
Relay outputRelay output
external deviceexternal device
max. 250 Vac/max. 250 Vac/ddcc
N N //
22AA
Figure 6-44: Relay outputsFigure 6-44: Relay outputs
Terminal Terminal Description Description AA
maxmax
Term. Com.Term. Com.
A A B B Form Form A, A, N.O. N.O. make make contactcontact
TypeType
42 42 41 41 Relay Relay output output [R [R 01]01]
{all}{all}
Ready for operation &Ready for operation &
LogicsManager
LogicsManager
N.O.N.O.
2.5 mm²2.5 mm²
4343
4646
Relay output [R 02]Relay output [R 02]
{all}{all}
Centralized alarm orCentralized alarm or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
44 44 Relay Relay output output [R [R 03]03]
{all}{all}
Starter orStarter or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
45 45 Relay Relay output output [R [R 04]04]
{all}{all}
Fuel solenoid / gas valve orFuel solenoid / gas valve or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
48 48 47 47 Relay Relay output output [R [R 05]05]
{all}{all}
Preglow orPreglow or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
50 50 49 49 Relay Relay output output [R [R 06]06]
{0}{0}
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
{1o}{1o}
{1oc}{1oc}
Command: close GCBCommand: close GCB
N.O.N.O.
{2oc}{2oc}
52 52 51 51 Relay Relay output output [R [R 07]07]
{0}{0}
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
{1o}{1o}
Command: open GCBCommand: open GCB
N.O.N.O.{1oc}{1oc}
{2oc}{2oc}
54 54 53 53 Relay Relay output output [R [R 08]08]
{0}{0}
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
{1o}{1o}
{1oc}{1oc}
{2oc}{2oc}
Command: close MCBCommand: close MCB
N.O.N.O.
56 56 55 55 Relay Relay output output [R [R 09]09]
{0}{0}
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
{1o}{1o}
{1oc}{1oc}
{2oc}{2oc}
Command: open MCBCommand: open MCB
N.O.N.O.
5757
6060
Relay output [R 10]Relay output [R 10]
{all}{all}
Auxiliary services orAuxiliary services or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
58 58 Relay Relay output output [R [R 11]11]
{all}{all}
Alarm class A and B orAlarm class A and B or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
59 59 Relay Relay output output [R [R 12]12]
{all}{all}
Alarm class C, D, E, F orAlarm class C, D, E, F or
LogicsManager
LogicsManager
SWSW
2.5 mm²2.5 mm²
LogicsManager
LogicsManager
..using the ..using the functionfunctionLogicsManagerLogicsManagerit is it is possible to freely program the relayspossible to freely program the relays
{all}-all appliction modes{all}-all appliction modes
{0}-no breaker mode; {1o}-GCB open; {1oc}-GCB open/close; {1oc}-GCB/MCB open/close{0}-no breaker mode; {1o}-GCB open; {1oc}-GCB open/close; {1oc}-GCB/MCB open/close
SW-switchable via the software; SW-switchable via the software; N.O.-normally open (make) contactN.O.-normally open (make) contact
Table 6-27: Relay outputs - terminal assignmentTable 6-27: Relay outputs - terminal assignment
CAUTION
CAUTION
The discrete output "Ready for operation OFF" must be wired in The discrete output "Ready for operation OFF" must be wired in series with an emergency stop func-series with an emergency stop func-
tion. This means that it must be tion. This means that it must be ensured that the generator circuit breaker is ensured that the generator circuit breaker is opened and the engine isopened and the engine is
stopped if this discrete output is de-energeized. We stopped if this discrete output is de-energeized. We recommend to signal this fault independently fromrecommend to signal this fault independently from
the unit if the availability of the plant is important.the unit if the availability of the plant is important.
To Next Page
Loading...
Need help?
General
