Name: Yaesu FT-710
Brand: Yaesu
Rating: 4 (1 reviews)

To Next Page

Operation Manual

FT-710

Table of Contents4
General Description6
Safety Precautions8
Accessories & Options10
Installation and Interconnections11
Antenna Considerations11
Antenna Connections11
Power Cable Connections11
Microphone, Headphone, Key, Keyer and FH-2 Connections12
Linear Amplifier Interconnections13
VL-1000 Linear Amplifier Interconnections13
Display Connections14
Remote Operation (LAN Unit "SCU-LAN10") Connection14
AESS (Acoustic Enhanced Speaker System)15
Connections15
Rear Panel16
Tuner/Linear16
Ant16
Gnd16
Ext Spkr16
Rem/Alc16
Key16
Rtty/Data16
Usb16
USB Jack16
SSM-75E Microphone Switches17
Display Indications18
Meter Display19
Operation MODE Display19
Operation Status Display19
HI-SWR Display19
Frequency Display (VFO-A)20
Keyboard Frequency Entry20
Tuning in 1 Mhz or 1 Khz Steps20
Frequency Display (VFO-B)20
When the Clarifier Function Is Active20
Operation of the Display [FUNC] Knob21
Filter Function Display22
Turn the Spectrum Display off22
Information Displayed on the Scope Screen22
Important Receiver Settings23
ATT (Attenuator)23
Ipo23
DNF (Digital NOTCH Filter)23
AGC (Automatic Gain Control)23
Information Displayed on the Scope Screen24
Scope Display Setting24
Center/Cursor/Fix24
Center24
Cursor24
Fix25
3Dss25
Multi25
Expand26
Span26
Speed26
Set with the FUNC Knob27
Level27
Peak27
Marker28
Color28
Adjust Contrast28
Adjusting the Brightness (DIMMER)28
Other Display Settings29
Screen Saver29
Inputting the Call Sign29
Front Panel Controls & Switches32
ON/OFF (LOCK) Switch32
SD Memory Card Slot32
Tune32
Vox/Mox32
Adjusts the VOX GAIN32
Adjusts the VOX Delay Time32
Adjusts the VOX Anti-Trip Sensitivity33
PHONES Jack33
MIC33
MAIN Dial33
Wire Stand33
Step Mch34
DSP Interference Removal Functions34
Shift35
Width35
Notch35
Contour36
Adjusting the GAIN of the CONTOUR Circuit36
Sets the Bandwidth ("Q") of the CONTOUR Circuit36
Apf36
Dsp Reset36
DNR (Digital Noise Reduction)37
Adjusting the DNR Level37
A/B37
BAND (Operating Band Selection)37
QMB (Quick Memory Bank)37
QMB Channel Storage37
QMB Channel Recall37
Changing the Number of QMB Channels37
VMI (VFO Mode Indicator)38
BUSY/TX Indicator38
NAR (Narrow)38
Fine/Fast38
Rf Gain/Sql39
Switching the Operation of the [RF GAIN/SQL] Knob39
Af Gain39
MODE (Operating Mode Selection)39
Zin/Spot40
Split40
CLAR (Clarifier)40
RX Clarifier40
Adjust Transmit Frequency to the Offset Frequency40
TX Clarifier41
To Offset the Frequency with the TX Clarifier Adjust Receive Frequency41
Adjusting the Noise Blanker Level41
Adjusting the Noise Attenuation41
Reduces Longer Duration Pulse Noise41
Voice Communications (SSB and AM)42
When Transmitting in SSB or am Mode42
Set with the FUNC Knob42
Speech Processor43
RF Power Output Control43
MONI (Monitor)43
Parametric Microphone Equalizer44
Setup the44
Activate the44
Voice Memory46
Record the Received Audio47
Play the Recorded Content47
Erase the Recorded Content47
Adjustable Receiver Audio Filter48
Change the Sound Quality of the Received Audio49
Using the Automatic Antenna Tuner50
CW Mode Operation51
Adjusting the Sidetone Audio Level51
CW Delay Time Setting51
CW Spotting (Zero-Beating)51
Setting of the Electronic Keyer52
Adjusting the Keyer Speed52
Setting the Keyer Weight (Dot/Dash) Ratio52
Reversing the Keyer Polarity52
Selecting the Keyer Operating Mode52
Contest Memory Keyer53
Message Memory53
Storing a Message into Memory53
Message Memory Programming53
(Using Your Paddle)53
Checking the CW Memory Contents54
On-The-Air CW Message Playback54
TEXT Memory55
Text Memory Storage55
Text Message Programming55
Checking the CW Memory Contents56
On-The-Air CW Message Playback56
FM Mode Operation57
Repeater Operation57
Tone Squelch Operation57
DATA (FT8 / RTTY / PSK) Operation58
Connecting to a Personal Computer58
FT8 Operation59
RTTY Operation60
PSK Operation60
Memory Operation62
M ► V62
Moving Memory Data to the VFO Register62
Transfer Last Used Memory to VFO62
Memory Storage62
Recall a Memory Channel Other than the Last Used VFO Frequency63
Memory Tune Operation63
Memory Groups63
Choosing the Desired Memory Group63
Erasing Memory Channel Data64
Check Memory Channel Status64
Labeling Memories64
Displaying the Memory Tag64
Scan Skip Setting65
60-Meter (5 Mhz) Band (U.S. Version Only)65
VFO and Memory Scanning66
Vfo/Memory Scan66
Programmable Memory Scan (PMS)67
Other Functions68
Band Stack Operation68
TOT (Time out Timer)68
Operation on Alaska Emergency Frequency: 5167.5Khz (U.S. Version Only)68
Screen Capture69
Using the SD Card70
Formatting a SD Card70
Saving Memory Data and Setting Menu Data71
Reading Memory and Set Menu Data72
Display the SD Card Information72
Setting Menu73
Optional Accessories102
External Automatic Antenna Tuner102
(For Wire Antenna)102
Active-Tuning Antenna System (ATAS-120A)104
Remote Control Switches105
Carrying Handle MHG-1106
Mounting Bracket SMB-209106
Resetting the Microprocessor107
Specifications108
Index110
Yaesu Limited Warranty112
Display the Certifications of114
FCC and CANADA114

Brand	Yaesu
Model	FT-710
Category	Transceiver
Language	English

Yaesu FT-710 User Manual

Table of Contents

Other manuals for Yaesu FT-710

Questions and Answers:

Yaesu FT-710 Specifications

Related product manuals