Yaesu FT-710 User Manual

38
ZIN/SPOT
ZIN
Press the [ZIN/SPOT] switch momentarily to adjust
the receiving frequency and zero-in automatically
while receiving a CW signal.
SPOT
While pressing and holding [ZIN/SPOT], the tone is
output from the speaker. This tone corresponds to
the pitch of your transmitted signal. If you adjust the
receiver frequency until the pitch of the received
CW signal matches that of the Spot tone, the trans-
mitted signal will be precisely matched to that of the
other station.
The Spot tone audio level may be adjusted by
pressing the [FUNC] knob, then touching [MONI
LEVEL], and rotating the [FUNC] knob.
SPLIT
A powerful capability of the FT-710 is its exibility
in Split Frequency operation using the VFO-A and
VFO-B frequency registers. This makes the FT-
710 especially useful for high-level DX-peditions.
The Split operation capability is very advanced and
easy to use.
1. Press the [A/B] key, then set the upper VFO fre-
quency to the desired receive frequency.
2. Press the [SPLIT] key, and then set the lower
VFO frequency to the desired transmit frequen-
cy.
During Split operation, the upper VFO register will
be used for reception, while the lower VFO register
will be used for transmission. Press the [SPLIT] key
again to cancel Split operation.
● Rotate the main dial while holding down the
[STEP • MCH /
] knob during split operation
will change the transmit and receive frequencies
in the same step at the same time.
● The receive and transmit frequencies can be set
to di󰀨erent bands or operation modes.
● During split operation, touch [TXW] after pressing
the [FUNC] knob, to receive the transmit frequen-
cy while pressing the [FUNC] knob.
● Press and hold the [SPLIT] key to change the re-
ceive frequency.
CLAR (Clarier)
The clarifier is used to adjust the transceiver re-
ceive frequency to match the other station transmit
frequency and improve the audio; or to shift the
transmit frequency of this station when the transmit
frequency of the contact station is shifted.
The display will indicate “CLAR RX” → “CLAR TX”
→ “CLAR RXTX” in red, each time the [CLAR] key
is pressed, and the clarier will activate.
Turning the MAIN dial changes the clarifier offset
frequency.
To turn the clarifier OFF, repeatedly press the
[CLAR] key until the Clarier status is not displayed.
To clear out the programmed clarifier offset alto-
gether, and reset it to “zero,” press and hold the
[CLAR] key.
•
RX Clarier
If the transmit frequency of the contact station
deviates, this receiver clarifier frequency can
be changed leaving this transmit frequency un-
changed.
1. Press the [CLAR] key.
2. Rotate the MAIN dial knob to change only the
receive frequency.
When the receive frequency is offset by +20Hz.
O󰀨sets of up to ±9995Hz may be set using
the Clarier.
3. To cancel Clarifier operation, press the [CLAR]
key three times.
● Since the o󰀨set amount is memorized, when the
clarier function is operated again, the same o󰀨-
set amount is set.
• Adjust transmit frequency to the
o󰀨set frequency
After changing the receiver frequency with RX
Clarier, the transmitter frequency can be set to the
same frequency as the receiver.
1. After o󰀨setting the receiver frequency, press the
[CLAR] key twice.
The transmit frequency becomes the same as
the receive frequency.
“CLAR RX” of the display changes to “CLAR
RXTX”.
2. Press the [CLAR] key twice, only the receive fre-
quency returns to the o󰀨set state.
“CLAR RXTX” of the display changes to “CLAR
RX”.

Yaesu FT-710 Specifications

General

Brand	Yaesu
Model	FT-710
Category	Transceiver
Language	English