ENGLISH
mg
Set the distance between the listening position
and
the various
speakers to
no
more than 20.0
ft
(6.00 metersl.
,~-
I
from
me
Select unit for distance.
II'Distance
Set distance from listening position to speakers.
Before making-."the •settings, measure thedista"nCe
lis"teningcpOsition
to
the
aifferent speakers.
Step
Feet /
Meters
Select step. (smallest distance)
Select the speaker you want to set, then set the distance.
Set the value closest to the measured distance.
Resets the settings to the default values.
Default
Distance measurement
[Variable range]
O.Oft
-
&a.Oft
:Display when "Feet"
is
set.
0.00m
-18.00m :Display when
"Meters"
is
set.
[Selectable
items]
I
1ft
"I
o.1ft
:
Can
be
selected
when"
Feet"
is
set.
I
aim
I
O;01m
:
Can
be selected when
"Meters"
is
set.
• Subwoofer Setup
Select
low
range signal to be reproduced bysubwoofer.
- Select "Large" or "Small" not according to the physical
size
of the
speaker but according to the low frequency reproduction capabilities
based on the frequency set at "Crossover Frequency"
(&page
31).
-When
"Front Speaker"
is
set to "Small", "Subwoofer"
can
automatically set to "Yes".
-If
"Subwoofer"
is
set to
"No",
"Front Speaker"
is
automatically set
to "Large".
-If
"Surround Speaker"
is
set to "None", "Surround
Back
Speaker"
are
automatically set to "None".
- When "Front Speaker"
is
set to "Small", "Center Speaker"
can
not
be
set to "Large".
- When using just one surround back speaker, connect it to the left
channel (SBU
[Selectable
items]
LFE
I:
Play
low range
and
LFE
signal of channels set to
"Small".
LFE+Main
:
Play
low
range
and
LFE
signal of
all
channels.
~,;
- This
can
be
set when menu "Speaker Configuration" - "Subwoofer"
is
set to
"Yes".
-
Play
music or a movie source
and
select the mode offering the
strongest
bass.
- Select "LFE+Main" if you want the bass signals to always
be
produced from the subwoofer.
Large
:Select this when using large speakers with ample low
frequency reproduction capabilities.
Small
:Select this when using small speakers without ample low
frequency reproduction capabilities.
None
:Select this when
no
speaker
is
connected.
Yes
:Select this when a subwoofer
is
connected.
No
:Select this when no subwoofer
is
connected.
Surround
Back Speaker
Even
when
the
Surround Back Speaker
setting
is
other
than
"None';
sound
may
not
be
emitted
from
the
surround back
speaker,
depending
on
the
playback source. In
this
case, make
a
menu
"Parameter"
-
"Surround
Parameter"
-
"SB
CH
Out"
setting
other
than
"OFF"
(@"page
48).
Select surround speakers use
and
size.
[Selectable
items]
Large'
I
Small
I
None
Surround
Speaker
Select surround
back
speaker use
and
size.
[Selectable
items]
(
Large
I
Small
I
None
)
(l2spkrs I
1spkr
)
INti
••
Since
"Amp
Assign" of AVR-1909
is
set to "ZONE2" by default,
audio
is
not output from the surround back speakers. When using the
surround back speakers with MAIN
ZONE,
change the "Amp Assign"
setting to "7.1 ch"
(&page
35).
2spkrs
1spkr
Select the number
of
surround back speakers.
For
details
on
how
to
select, set and cancel settings
for
each menu, see
"Menu
Operations"
(Gf'page
22}.1
30
To Next Page
Loading...
Need help?
General
