ENGLISH
[Selectable items]
[Selectable items]
[Selectable items]
Audyssey
Byp.
UR
Optimize frequency response
of
speakers
except front Land R speakers.
Audyssey
Rat
Optimize frequency response of
all
speakers
to flat response.
Manual
Apply frequency response set with "Manual
EO"
(~page
34).
OFF
I.
Turn equalizer off.
~
• Audyssey - Audyssey
Byp.
UR
~
L---
OFF
__
Manual
--
Audyssey Flat -------J
Audyssey Settings
Select room equalizer for current environment.
~
Operating from the main unit or main remote
control unit
Press
MULlED
-When
"Audyssey", Audyssey
Byp.
UR" or "Audyssey Flat"
is
selected, "
~~~~~SEY
" lights.
- After running Auto Setup, if the Speaker Configuration, Distance,
Channel
Level,
and Crossover Frequency have changed without
increasing the number of speakers measured, only
"~~~SEY"
lights.
Select the type of room correction desired from the following list.
Audyssey
Optimize frequency response
of
all
speakers.
III
MultEQ
- "Audyssey", "Audyssey Byp.
UR"
and
"Audyssey Flat"
can
be
selected after the auto setup procedure
has
been performed.
- After performing "Auto Setup", the
"MultEO"
setting automatically
becomes "Audyssey".
-If
the settings of speakers for which "None"
has
been determined
at "Auto Setup"
are
changed, "Audyssey': "Audyssey Byp.
UR"
and
"Audyssey Flat" cannot
be
selected. Either perform Auto Setup
again,
or return to the setting after running Auto Setup with "Auto
Setup" - "Parameter Check" - "Restore".
- MultEO
and
Manual
EO
set to "Not Used" with "Manual Setup"
- "Audio Setup" - "EO Preset" - "EO Customize" ((1Tpage
34)
on
the menu, cannot
be
selected.
- When using headphones,
"MultEO"
is
set to "OFF':
-6dB -+&IB
-6dB-+6dB
"Bass"
and
"Treble"
can
be
set when "Tone Control"
is
set to "ON':
Tone
Adjust the tonal quality
of
the sound.
[Selectable items]
ON
Allow tone adjustment (treble,
bass).
OFF
Playback
without tone adjustment.
Adjust low frequency range
(bass).
[Variable range]
[Variable range]
it Treble
Adjust high frequency range (treble).
1m
Tone
Control
Turn
tone adjustments off.
The
tone cannot be adjusted when
in
the
DIRECT
mode.
-N"·-
When the "Dynamic EO" setting
is
"ON': setting
is
not possible.
1m
Bass
The
input from the subwoofer channel
is
not attenuated.
Usually use
in
this mode.
The input from the subwoofer channel
is
attenuated.
[Selectable items]
~.
The subwoofer
is
used.
OFF
.
The
subwoofer
is
not used.
Resets the settings to the default values.
Attenuate subwoofer level when using
EXT
IN
mode.
ON
The
surround
back
channel signal
is
played.
OFF
The
surround
back
channel signal
is
not played.
III
SB
CH
Out (for 2-channel sources)
Determine whether to
use
surround
back
speakers.
..
Default
lID
SW
ATT (SUBWOOFERATT.)
ON
~.
·iI~
Set this to
"ON"
if the subwoofer channel level seems too high when
playing audio signal.
1m
Subwoofer
Turn
subwoofer output
on
and
off.
n
o
::l
::l
~
~
o'
::l
'"
I
49 IFor details
on
adjusting individual parameters, see "Adjusting the parameters"
(~page
46).
To Next Page
Loading...
Need help?
General
