Denon AVR-887 User Manual

ENGLISH
ENGLISH
63
Advanced Setup – Part 2Advanced Setup – Part 2
• The crossover frequency mode is valid only when subwoofer is set
to “ON”, and when one or more speakers are set to “Small”, as
described in section “Setting the Speaker Configuration” ( page
60).
• If “LFE+Main” is set at “Subwoofer Setup”, “SW:LFE+Main” (
page 61) is displayed at the top right of the screen.
• Set to “80 Hz” when using regular speakers. When using small
speakers, we recommend setting to a higher frequency.
Others Setup
Setting the Room Equalizer Setup
Set the Room Equalizer setting with “All” or “Assign” for each
surround mode.
Press
FF GG
to set, then press ENTER.
All:
Sets the equalizer for all surround modes.
Assign:
Sets the equalizer individually for each surround mode ( page
28).
When “All” is selected:
Press
FF GG
to set.
OFF:
The equalizer is not used.
Normal:
Adjust the frequency response of all speaker suitable for general
surround system.
Front:
Adjusts the frequency response of the surround speakers to match
the characteristics of the front channel speakers.
Flat:
Adjusts the frequency response of all speakers to the flattest
response. This mode is suitable for multi-channel music surround
sound sources.
Manual:
Selects the setting value that was set in the “Setting the Manual
Equalizer Setup” ( page 57).
Press
DD HH
to select “Room EQ Setup”, then press
ENTER.
1
2
3
Press ENTER.
4
Setting the Crossover Frequency
Set the frequency (Hz) below which the bass sound of the various
speakers is to be output from the subwoofer.
For speakers that are set to “Small”, frequencies under the crossover
frequency are cut before the signal is output, and the low frequency
component that was cut is output from the subwoofer or the
speakers that are set to “Large”.
Press
DD HH
to select “Crossover Frequency”, then
press ENTER.
1
Press
FF GG
to set.
40, 60, 80, 90, 100, 110, 120, 150, 200, 250 Hz:
Set as desired according to your speakers’ bass playback ability.
2
Press ENTER.
3
1
2
• The equalizer setting of “Normal”, “Front” and “Flat” can be
selected after performing the Auto Setup.
• When the speaker set as “None” with the Auto Setup is changed to
on manually, the equalizer of “Normal”, “Front” and “Flat” cannot
be used.
• When headphones are connected, the Room Equalizer cannot be
used.
1
2
3

Denon AVR-887 Specifications

Power

rated output front	100 W + 100 W (8 ohms, 20 Hz - 20 kHz, 0.08 % THD)
rated output front alternative	135 W + 135 W (6 ohms, 1 kHz, 0.7 % THD)
rated output center	100 W (8 ohms, 20 Hz - 20 kHz, 0.08 % THD)
rated output center alternative	135 W (6 ohms, 1 kHz, 0.7 % THD)
rated output surround	100 W + 100 W (8 ohms, 20 Hz - 20 kHz, 0.08 % THD)
rated output surround alternative	135 W + 135 W (6 ohms, 1 kHz, 0.7 % THD)
rated output surround back	100 W + 100 W (8 ohms, 20 Hz - 20 kHz, 0.08 % THD)
rated output surround back alternative	135 W + 135 W (6 ohms, 1 kHz, 0.7 % THD)
power supply	AC 120 V, 60 Hz
power consumption	5.5 A

Audio Inputs and Outputs

analog inputs	9 sets
analog ext inputs	8
digital inputs optical	4
digital inputs coaxial	2
audio delay function	0 - 200 msec.
variable subwoofer crossover	40/60/80/90/100/110/120/150/200/250 Hz

Video Inputs and Outputs

component video inputs	3 sets
composite inputs	5
s-video inputs	5
component video outputs	1 set
composite outputs	3
s-video outputs	3

Audio Performance

frequency response	10 Hz - 100 kHz (+1, -3 dB)
signal-to-noise ratio	100 dB (IHF-A weighted)
tone control treble	±6 dB at 10 kHz
tone control bass	±6 dB at 100 Hz

Weight and Dimensions

dimensions	17-3/32” (W) x 6-47/64” (H) x 16-27/64” (D)
dimensions metric	434 (W) x 171 (H) x 417 (D) mm
weight	29 lbs 5 oz
weight metric	13.0 kg