Epson TM-U295 User Manual

EPSON
TITLE
SHEET
REVISION
NO.
SHEETNEXT
F
TM-U295/U295P
Specification
(STANDARD)
29 28
2) Reverse feed commands are disabled.
In page mode, data can be written freely in the specified printing area. Therefore, the following
commands which feeds paper in reverse direction is disabled:
ESC K
, and
ESC e
3) Up-side down printing mode has no effect in page mode.
In page mode, characters and bit images can be rotated in increments of 90
°
, and also printing is
available any of four directions. Therefore, the
ESC {
command which turns on or off up-side down
printing mode has no effect in page mode.
4) Double-strike printing cannot be performed.
In page mode, data written twice to the same area is logically OR'ed before printing. Therefore,
double-strike mode cannot be used to emphasize characters.
5) Underline mode has no effect in page mode.
In page mode, because characters and bit images can be overlapped, underline by
ESC !
is not
drawn. But it becomes effective when printer returns to standard mode. In this case, bit images can be
used, instead of underline mode. (Broken line, wavy line, etc. are also available.)
3.9.3 Setting values in standard and page modes
1) The values set by commands are common to both standard and page modes. However, values are
set independently in each mode for
ESC SP
,
ESC 2
, and
ESC 3
.
2) Although the maximum number of printable dots for a bit image is 210 in standard mode, 480 bit-
image dots can be printed in the y direction (paper feeding direction) in page mode. This is possible
only when 480 printable-area dots in the y direction have been specified using
ESC W
, and the
printing direction value n in the
ESC T
command is 1 or 3).
3.9.4 Development of print data in the printing area
Development of print data in the printing area is performed as follows:
À
The printing area is set using
ESC W
. When all printing and feeding are complete before the printer
receives the
ESC W
command, the left side as you face the printer is taken as the origin (x0, y0) of
the printing area. The printing rectangular area is defined by the length (dx dots) extending from
and including the origin (x0, y0) in the x direction (perpendicular to the paper feed direction), and by
the length (dy dots) in the y direction (paper feed direction).
When the printer receives print data after
ESC W
sets the printing area and
ESC T
sets the printing
direction, the print data is developed within the printing area so that the highest dot of the print data is
at the beginning of the printing area. (See the
ESC *
**
*
command description in Section 6.2 and
Appendix F)
Since print data containing double-height and quadruple-size characters is developed so that only the
lower 7 dots of these characters are included in the printing area, execute a line feed (
LF
) before the
print data to allow the remaining higher dots to be printed.

Epson TM-U295 Specifications

General

Color	No
Maximum number of copies	2 copies
Maximum printing width (columns)	42
Dimensions (WxDxH)	180 x 190.5 x 101.5 mm
Power requirements	24 VDC±10%
Connectivity technology	Wired
Printing media thickness	0.09/0.35 µm
Mean time between failures (MTBF)	180000 h
Safety	UL, CSA C22.2 No. 950
Country of origin	Japan
Electromagnetic compatibility	VCCI class A, FCC class A, CE marking
Pallet width	1200 mm
Pallet height	1000 mm
Pallet length (UK)	1370 mm
Quantity per pallet	120 pc(s)
Quantity per pallet (UK)	160 pc(s)
Master (outer) case width	300 mm
Quantity per pallet layer	24 pc(s)
Master (outer) case height	405 mm
Master (outer) case length	485 mm
Harmonized System (HS) code	84433210
Quantity per pallet layer (UK)	32 pc(s)
Quantity per master (outer) case	4 pc(s)
Package depth	270 mm
Package width	235 mm
Package height	185 mm
Package weight	1845 g
Quantity per pack	1 pc(s)

Weight and Dimensions

Depth	191 mm
Width	180 mm
Height	102 mm
Weight	1600 g