Beforeuse
31
Rubber
grommet
Brass eyelet
Wood screw
Servo mount
2.3-2.6mm nut
washer
Rubber
grommet
Brass eyelet
Servo mount
2.3-2.6mm screw
(Helicopter) (Airplane/Glider)
6HUYROHDGZLUHV
To prevent the servo lead cable from being
EURNHQE\YLEUDWLRQGXULQJIOLJKWSURYLGHD
little slack in the cable and fasten it at suitable
points. Periodically check the cable during daily
maintenance.
Fasten about 5-10cm
from the servo outlet so
that the lead wire is neat.
Margin in the lead wire.
MOUNTINGTHEPOWER
SWITCH
:KHQPRXQWLQJDSRZHUVZLWFKWRDQDLUIUDPH
make a rectangular hole that is a little larger than
the total stroke of the switch so that you can turn
the switch ON/OFF without binding.
Avoid mounting the switch where it can be
FRYHUHGE\HQJLQHRLODQGGXVW,QJHQHUDOLWLV
recommended to mount the power switch on the
VLGHRIWKHIXVHODJHWKDWLVRSSRVLWHWKHPXIÀHU
SAFETYPRECAUTIONS
when
youinstallreceiverandservos
:DUQLQJ
&RQQHFWLQJFRQQHFWRUV
%HVXUHWRLQVHUWWKHFRQQHFWRUXQWLOLW
VWRSVDWWKHGHHSHVWSRLQW
+RZWRSURWHFWWKHUHFHLYHUIURP
YLEUDWLRQDQGZDWHU
:UDSWKHUHFHLYHUZLWKVRPHWKLQJVRIW
VXFKDVIRDPUXEEHUWRDYRLGYLEUDWLRQ
,IWKHUHLVDFKDQFHRIJHWWLQJZHWSXW
WKHUHFHLYHULQDZDWHUSURRIEDJRU
EDOORRQWRDYRLGZDWHU
5HFHLYHUVDQWHQQD
1HYHUFXWWKHUHFHLYHUVDQWHQQD'R
QRWELQGWKHUHFHLYHUVDQWHQQDZLWKWKH
FDEOHVIRUVHUYRV
/RFDWHWKHUHFHLYHUVDQWHQQDDVIDUDV
SRVVLEOHIURPPHWDOVRUFDUERQILEHU
FRPSRQHQWVVXFKDVIUDPHVFDEOHVHWF
*Cutting or binding the receiver's antenna will
UHGXFHWKHUDGLRUHFHSWLRQVHQVLWLYLW\DQGUDQJH
and may cause a crash.
6HUYRWKURZ
$GMXVW\RXUV\VWHPVRWKDWSXVKURGV
ZLOOQRWELQGRUVDJZKHQRSHUDWLQJWKH
VHUYRVWRWKHIXOOH[WHQW
,IH[FHVVLYHIRUFHLVFRQWLQXRXVO\DSSOLHGWRD
VHUYRWKHVHUYRFRXOGEHGDPDJHGGXHWRIRUFH
on the gear train and/or power consumption
causing rapid battery drain.
0RXQWLQJVHUYRV
8VHDYLEUDWLRQSURRIUXEEHUVXFKDV
UXEEHUJURPPHWXQGHUDVHUYRZKHQ
PRXQWLQJWKHVHUYRRQDVHUYRPRXQW
$QGEHVXUHWKDWWKHVHUYRFDVHVGRQRW
WRXFKGLUHFWO\WRWKHPHWDOSDUWVVXFKDV
VHUYRPRXQW
,IWKHVHUYRFDVHFRQWDFWVWKHDLUIUDPHGLUHFWO\
vibration will travel to and possibly damage the
servo.
MOUNTINGTHESERVO